Emotron VFX/FDU 2.0

More documents

Recommendations

Info

Supply ID run [O15]Identification run to measure and set up supply parameters.Default:Off 0OffOn 1 Activate the supply ID-runSupply Auto [O16]Automatic activation of supply parameter identificationafter every power-up.Default:Off 0OffOn 1 Activate automatic ID-runVolt sensor [O17]Supply voltage sensor option.Default:Off 0O15 Supply IDrunStpOffO16 Supply AutoStpOffO17 Volt sensorStpPosOffOn 1 Activate supply voltage measurement.NOTE: Requires supply voltage measurement hardwareoption.9.9.2 Charge/Startparameters [O20]Main menu for charge control and start/stop parameters.Charge control [O21]DC-link Charge relay control function. .Default:Supply - NC 0Supply - NO 1Run-NO 2Enable - NO 3Supply - NCCharge at power supply via NC terminalon Relay 1.Charge at power supply via NO terminalon Relay 1.Charge at run command via NO terminalon Relay 1.Charge at Enable command via NOterminal on Relay 1.NOTE: Normally open (NO) alternatives requires 24 VStanby supply option.Start Mode [O22]Start/Stop mode. If set to “Regen” AFR starts onregenerative demand..Default:O21StpO22StpStandardCharge CtrlSupply-NCRun/Stp ModeStandardStandard 0 AFR active via Run commandRegen 1AFR active only if regenerationrequired and valid run command.NOTE: Regeneration mode requires supply voltagemeasurement hardware option.Regeneration stop delay time [O23]Regeneration stop delay time after AFR in motoring mode.O23StpReg Stp Mode1sDefault:1sRange 0.0 - 10.0sNOTE: Regeneration mode requires supply voltagemeasurment.40 Functional Description for AFR unit <strong>Emotron</strong> AB 01-5076-01r1
9.9.3 Udc controller oparameters[O30]Main menu for DC-link voltage (Udc) parameters.Udc reference [O31]DC-link voltage reference value..O31 Udc refStp 1.05*UpeakUdc PI Charge limit [O36]Udc PI controller max charge limit during syncronization,i.e. during Udc charging.Default: 20%Range 0 - 100%O36 Udc PI ChargStp 20%Default:Range1.05*UpeakUpeak to UmaxUdc margin[O37]Udc reference control margin from actual output voltage.NOTE: Actual DC - link voltage reference value is limitedvia actual supply voltage and [O37 Udc margin].Udc ramp time [O32]Udc ramp time, defined as time from 0 ->1000V.Default:1sRange 0.0 - 10.0sUdc PI Gain controller [O33]Proportional gain of Udc PI controller..Default: 5.0Range 0.0 - 10.0Udc PI Time controller [O34]Integral time constant of Udc PI controller.Default: 0.2sRange 0.0 - 10.0sUdc PI Max limit [O35]Udc PI controller max limit, i.e. active power limit.Default: 200%Range 0 - 400%O32 Udc rampStp1sO33 Udc PI GainStp 5.0O34 Udc PI TimeStp 0.2sO35 Udc PI MaxStp 200%Default: 5%Range 0.0 - 20.0%NOTE: Actual internal DC - link voltage reference value islimitegd via actual supply voltage and [O37 Udc margin],i.e.where Uac is actual supply voltage.9.9.4 Reactive power (Q) controllerparameters [O40]Q Max limit [O41]Reactive power max. limit value, i.e. amount of unusedovercapacity that is allowed for Q - compensation.Default: 0%Range 0 to 100%NOTE: Reactive power limited internally by the actualactive power.Q ramp time [O42]Q ramp time, defined as time from 0->100%.Default:1sRange 0.0 - 10.0sO37 Udc marginStp 5%3 Uac 1 + O37O41 Q MaxStp 0%O42 Q rampStp1s<strong>Emotron</strong> AB 01-5076-01r1 Functional Description for AFR unit 41
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 20 and 21: 3.1.1 CoolingTable below shows the
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33 and 34: 8. Operation via the Control PanelT
Page 35 and 36: 8.3.3 LED indicatorsThe symbols on
Page 37 and 38: 8.4 The menu structureThe menu stru
Page 39 and 40: 9. Functional Description for AFR u
Page 41 and 42: Reset Control [216]When the AFR is
Page 43 and 44: Reactive power [714]Displays the ac
Page 45: 9.8 System Data [900]Main menu for
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?