Emotron VFX/FDU 2.0

More documents

Recommendations

Info

8.3 The control panelLOC/REMRESETLC DisplayLEDsControl KeysToggle KeyArea E:Area F:SST : Operating Safe Stop, is flashing whenactivatedLCL : Operating with low cooling liquid levelShows active parameter set and if it is a motorparameter.Shows the setting or selection in the active menu.This area is empty at the 1st level and 2nd levelmenu. This area also shows warnings and alarmmessages. In some situations this area couldindicate +++ or - - - please see furtherinformation in chapter 8.3.2 page 28PREV NEXT ESCENTERFunction Keys300 Process ApplStpAFig. 23 Example 1st level menuFig. 21 Control panel8.3.1 The displayThe display is back lit and consists of 2 rows, each withspace for 16 characters. The display is divided into six areas.The different areas in the display are described below:A221TMotor VoltStpAM1: 400VDBEFig. 22 The displayCFArea A: Shows the actual menu number (3 or 4digits).Area B Shows if the menu is in the toggle loop or theVSI is set for Local operation.Area C: Shows the heading of the active menu.Area D: Shows the status of the VSI (3 digits).The following status indications are possible:Acc : AccelerationDec : DecelerationI 2 t : Active I 2 t protectionRun : Motor runsTrp : TrippedStp : Motor is stoppedVL : Operating at Voltage limitSL : Operating at Speed limitCL : Operating at Current limitTL : Operating at Torque limitOT : Operating at Temperature LimitLV : Operating at Low VoltageSby : Operating from Standby power supply220 Motor DataStpAFig. 24 Example 2nd level menu221 Motor VoltStp M1: 400VAFig. 25 Example 3d level menu4161 Max AlarmStp 0.1sAFig. 26 Example 4th level menu8.3.2 Indications on the displayThe display can indicate +++ or - - - if a parameter is out ofrange. In the VSI there are parameters which are dependenton other parameters. For example, if the speed reference is500 and the maximum speed value is set to a value below500, this will be indicated with +++ on the display. If theminimum speed value is set over 500, - - - is displayed.28 Operation via the Control Panel <strong>Emotron</strong> AB 01-5076-01r1
8.3.3 LED indicatorsThe symbols on the control panel have the followingfunctions:RunGreenFig. 27 LED indicationsTable 11SymbolPOWER(green)LED indicationFunctionON flashing OFFPower on ---------------- Power offTRIP (red) Tripped Warning/Limit No tripRUN(green)RunningAC drive speedincrease/decrease (VSIonly)AFR/VSIstoppedNOTE: If the control panel is built in, the back light of thedisplay has the same function as the Power LED in Table11 (Blank panel LEDs).8.3.4 Control keysThe control keys are used to give the Run, Stop or Resetcommands directly. As default these keys are disabled, set forremote control. Activate the control keys by selectingKeyboard in the menus Ref Control [214] and Reset Ctrl[216].If the Enable function is programmed on one of the digitalinputs, this input must be active to allow Run/Stopcommands from the control panel.Table 12RESETControl keysRUN L:TripRedSTOP/RESET:PowerGreengives a start withleft rotationstops or resets8.3.5 The Toggle and Loc/Rem KeyThis key has two functions: Toggle andswitching between Loc/Rem function.LOC/ Press one second to use the toggle functionREMPress and hold the toggle key for more thanfive seconds to switch between Local and Remote function,depending on the settings in [2171] and [2172].When editing values, the toggle key can be used to changethe sign of the value, see section 8.6, page 32.Toggle functionUsing the toggle function makes it possible to easily stepthrough selected menus in a loop. The toggle loop cancontain a maximum of ten menus. As default the toggle loopcontains the menus needed for Quick Setup. You can use thetoggle loop to create a quick-menu for the parameters thatare most importance to your specific application.NOTE: Do not keep the Toggle key pressed for more thanfive seconds without pressing either the +, - or Esc key,as this may activate the Loc/Rem function of this keyinstead. See menu [217].Add a menu to the toggle loop1. Go to the menu you want to add to the loop.2. Press the Toggle key and keep it pressed while pressingthe + key.Delete a menu from the toggle loop1. Go to the menu you want to delete using the toggle key.2. Press the Toggle key and keep it pressed while pressingthe - key.Delete all menus from the toggle loop1. Press the Toggle key and keep it pressed while pressingthe Esc key.2. Confirm with Enter. The menu Preferred view [100] isdisplayed.Default toggle loopFig. 28 shows the default toggle loop. This loop contains thenecessary menus that need to be set before starting. PressToggle to enter menu [211] then use the Next key to enterthe sub menus [212] to [21A] and enter the parameters.When you press the Toggle key again, menu [221] isdisplayed.RUN R:gives a start withright rotationNOTE: It is not possible to simultaneously activate theRun/Stop commands from the keyboard and remotelyfrom the terminal strip (terminals 1-22).<strong>Emotron</strong> AB 01-5076-01r1 Operation via the Control Panel 29
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 20 and 21: 3.1.1 CoolingTable below shows the
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33: 8. Operation via the Control PanelT
Page 37 and 38: 8.4 The menu structureThe menu stru
Page 39 and 40: 9. Functional Description for AFR u
Page 41 and 42: Reset Control [216]When the AFR is
Page 43 and 44: Reactive power [714]Displays the ac
Page 45 and 46: 9.8 System Data [900]Main menu for
Page 47 and 48: 9.9.3 Udc controller oparameters[O3
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?