Emotron VFX/FDU 2.0

More documents

Recommendations

Info

9.7 View Trip Log [800]Main menu with parameters for viewing all the logged tripdata. In total the AFR saves the last 9 trips in the tripmemory. The trip memory refreshes on the FIFO principle(First In, First Out). Every trip in the memory is logged onthe time of the Run Time [731] counter. At every trip, theactual values of several parameter are stored and available fortroubleshooting.9.7.1 Trip Message log [810]Display the cause of the trip and what time that it occurred.When a trip occurs the status menus are copied to the tripmessage log. There are nine trip message logs [810]–[890].When the tenth trip occurs the oldest trip will disappear.Unit:Range:8x0 Trip messageStp h:mm:ssh: m (hours: minutes)0h: 0m–65355h: 59m810 Ext TripStp 132:12:14For fieldbus integer value of trip message, see message tablefor warnings, [722].NOTE: Bits 0–5 used for trip message value. Bits 6–15for internal use.Trip menu Copied from Description81G 726 Analogue input status 3-481H 727 Analogue output status 1-281L 731 Run Time81M 732 Mains Time81N 733 Energy81O 310 Process referenceExample:Fig. 33 shows the third trip memory menu [830]: Overtemperature trip occurred after 1396 hours and 13 minutesin Run time.Fig. 33 Trip 3830 Over tempStp 1396h:13m9.7.2 Trip Messages [820] - [890]Same information as for menu [810].9.7.3 Reset Trip Log [8A0]Resets the content of the 10 trip memories.8A0 Reset TripStpNoTrip message [811]-[81N]The information from the status menus are copied to thetrip message log when a trip occurs.Default:No 0Yes 1NoTrip menu Copied from Description811 711 Process Value813 713 Torque814 714 Reactive Power815 715 Electrical Power816 716 Current817 717 Output voltage818 718 Frequency819 719 DC Link voltage81A 71A Heatsink Temperature81C 721 VSI Status81D 723 Digital input status81E 724 Digital output status81F 725 Analogue input status 1-2NOTE: After the reset the setting goes automaticallyback to “NO”. The message “OK” is displayed for 2 sec.38 Functional Description for AFR unit Emotron AB 01-5076-01r1
9.8 System Data [900]Main menu for viewing all the AFR system data.9.8.1 AFR Data [920]AFR Type [921]Shows the AFR type according to the type number.The options are indicated on the type plate of the AFR.921 AFR2.0Stp AFR46-175Example of typeExamples:AFR46-175 suited for 380-460V mains supply and a ratedinput current of 175A.Software [922]Shows the software version number of the AFR.Fig. 34 gives an example of the version number.922 SoftwareStp V4.30-97.03Fig. 34 Example of software versionTable 15BitInformation for Modbus and Profibus number,software version7–0 minor13–8 major15–14Table 16BitV 4.30 = Version of the SoftwareDescriptionrelease00: V, release version01: P, pre-release version10: , Beta version11: , Alpha versionInformation for Modbus and Profibus number,option version7–0 minor15–8 majorDescription9.9 AFR Option [O00]Main menu for AFR dedicated settings.9.9.1 Supply parameters [O10]Main menu for power supply parameters.Supply Volts [O11]Nominal supply voltage.Default:Range:Supply Frequency [O12]Nominal supply frequency.Default:Range:400 V380 - 460 VSupply Current [O13]Nominal supply current. Only used for mains supplysynchronisation and overcurrent protection.Default:Range:50Hz50 - 60HzAFR. InomSupply Sequence [O14]Nominal phase sequence of supply.Default:Pos 0Neg 1O11 Supply VoltsStp400 VO12 Supply FreqStp50 HzO13 Supply CurrStp AFR. Inom0 - AFR. InomO14 Supply SeqStpPosPosPositive phase sequence,i.e. L1-L2-L3Negative phase sequence,i.e. L3-L2-L1NOTE: It is important that the software version displayedin menu [920] is the same software version number asthe software version number written on the title page ofthis instruction manual. If not, the functionality asdescribed in this manual may differ from thefunctionality of the AFR.Emotron AB 01-5076-01r1 Functional Description for AFR unit 39
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 20 and 21: 3.1.1 CoolingTable below shows the
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33 and 34: 8. Operation via the Control PanelT
Page 35 and 36: 8.3.3 LED indicatorsThe symbols on
Page 37 and 38: 8.4 The menu structureThe menu stru
Page 39 and 40: 9. Functional Description for AFR u
Page 41 and 42: Reset Control [216]When the AFR is
Page 43: Reactive power [714]Displays the ac
Page 47 and 48: 9.9.3 Udc controller oparameters[O3
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?