Emotron VFX/FDU 2.0

More documents

Recommendations

Info

100511 Toggle loop 211341LOC/REM331213241212Sub menusNEXT222Sub menusaccording to the selection in Keyboard Reference menu[369].Remote modeWhen the VSI is switched to REMOTE operation, the VSIwill be controlled according to selected control methods inthe menu’s Reference Control [214], Run/Stop Control[215] and Reset Control [216]. The actual operation statusof the VSI will reflect the status and settings of theprogrammed control selections, e.g. Start/Stop status andsettings of the programmed control selections, accelerationor deceleration speed according to the selected referencevalue in the menu Acceleration Time [331] / DecelerationTime [332].To monitor the actual Local or Remote status of the VSIcontrol, a “Loc/Rem” function is available on the DigitalOutputs or Relays. When the VSI is set to Local, the signalon the DigOut or Relay will be active high, in Remote thesignal will be inactive low. See menu Digital Outputs [540]and Relays [550].Fig. 28 Default toggle loopIndication of menus in toggle loopMenus included in the toggle loop are indicated with ain area B in the display.Loc/Rem functionThe Loc/Rem function of this key is disabled as default.Enable the function in menu [2171] and/or [2172].With the function Loc/Rem you can change between localand remote control of the VSI from the control panel. Thefunction Loc/Rem can also be changed via the DigIn, seemenu Digital inputs [520]Change control mode1. Press the Loc/Rem key for five seconds, until Local? orRemote? is displayed.2. Confirm with Enter.3. Cancel with Esc.NEXT228Local modeLocal mode is used for temporary operation. When switchedto LOCAL operation, the VSI is controlled via the definedLocal operation mode, i.e. [2171] and [2172]. The actualstatus of the VSI will not change, e.g. Run/Stop conditionsand the actual speed will remain exactly the same. When theVSI is set to Local operation, the display will show L inarea B in the display.The VSI will be started and stopped using the keys on thecontrol panel. The reference signal can be controlled usingthe + and - keys on the keyboard, when in the menu [310]T8.3.6 Function keysThe function keys operate the menus and are also used forprogramming and read-outs of all the menu settings.Table 13ENTERESCPREVNEXTFunction keysENTER key:ESCAPE key:PREVIOUS key:NEXT key:- key:+ key:Fig. 29 Menu structure- step to a lower menulevel- confirm a changedsetting- step to a highermenu level- ignore a changedsetting, withoutconfirming- step to a previousmenu within the samelevel- go to more significantdigit in edit mode- step to a next menuwithin the same level- go to less significantdigit in edit mode- decrease a value- change a selection- increase a value- change a selection30 Operation via the Control Panel Emotron AB 01-5076-01r1
8.4 The menu structureThe menu structure consists of 4 levels:Main Menu1st level2nd level3rd level4th levelThe first character in the menu number.The second character in the menu number.The third character in the menu number.The fourth character in the menu number.This structure is consequently independent of the numberof menus per level.For instance, a menu can have one selectable menu (Set/View Reference Value [310]), or it can have 17 selectablemenus (menu Speeds [340]).NOTE: If there are more than 10 menus within one level,the numbering continues in alphabetic order.300 Process and Application ParametersSettings more relevant to the application such as Reactivepower, Reference etc.500 Inputs/Outputs and VirtualConnectionsAll settings for inputs and outputs are entered here.600 Logical Functions and TimersAll settings for conditional signal are entered here.700 View Operation and StatusViewing all the operational data like frequency, load, power,current, etc.800 View Trip LogViewing the last 10 trips in the trip memory.900 Service Information and AFR DataElectronic type label for viewing the software version andAFR type.O00AFR OptionMain setup for AFR dedicated features8.5 Programming duringoperationMost of the parameters can be changed during operationwithout stopping the AFR or VSI. Parameters that can notbe changed are marked with a lock symbol in the display.NOTE: If you try to change a function during operationthat only can be changed when the AFR is stopped, themessage “Stop First” is displayed.41614162NG_06-F28Fig. 30 Menu structure (general principle)8.4.1 The main menu for AFRThis section gives you a short description of the functions inthe Main menu for AFR.For Emotron VFX and FDU refer to the standardinstruction manual.100 Preferred ViewDisplayed at power-up. It displays the actual process value asdefault. Programmable for many other read-outs.200 Main SetupMain settings to get the AFR operable. The supply datasettings are the most important. Also option utility andsettings.Emotron AB 01-5076-01r1 Operation via the Control Panel 31
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 20 and 21: 3.1.1 CoolingTable below shows the
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33 and 34: 8. Operation via the Control PanelT
Page 35: 8.3.3 LED indicatorsThe symbols on
Page 39 and 40: 9. Functional Description for AFR u
Page 41 and 42: Reset Control [216]When the AFR is
Page 43 and 44: Reactive power [714]Displays the ac
Page 45 and 46: 9.8 System Data [900]Main menu for
Page 47 and 48: 9.9.3 Udc controller oparameters[O3
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

Create successful ePaper yourself

Delete template?

Save as template?