Series 90-70 Genius Bus Controller Manual, GFK-2017

More documents

Recommendations

Info

35. Click Next.6. Review the settings for Redundancy Scheme and Bus Controller locations. Ifsettings are correct, click Finish. If you need to make changes, click Back.When you click Finish, two Genius busses are created and two Bus Controllers areadded to the PLC. The parameter settings of the second Bus Controller (except for therack and slot numbers and Serial Bus Address) are the same as for the first BusController. The two Bus Controllers are, by default, assigned Serial Bus Addresses 30and 31. Each bus contains an image of both Bus Controllers.3-22 Series 90-70 Genius® Bus Controller – July 2003 GFK-2017
3Redundancy Wizard: Generate Secondary Hardware Configuration from the CurrentConfigurationFor a Series 90-70 PLC, this wizard generates a secondary hardware configuration forthree CPU models: IC697CPU780/CGR772/CGR935. For more information aboutSeries 90-70 CPU redundancy for CPU models IC697CGR772 and IC697CGR935,please see the Series 90-70 Enhanced Hot Standby CPU Redundancy User's Guide,GFK-1527A. For information about redundancy for CPU model IC697CPU780, pleasesee the Series 90-70 Hot Standby CPU Redundancy User's Guide, GFK-0827. Bothdocuments are available online at GEFanuc.com.This wizard is available only if the current rack system contains a CPU780, CGR935,or CGR772, and the Redundancy Mode (on the CPU configuration Redundancy tab) isset to Primary.1. In the Redundancy wizard, select: Generate Secondary Hardware Configurationfrom the Current Configuration.2. Click Next.3. Select Mirror to Secondary Hardware Configuration or Generate SecondaryHardware Configuration in the following file.GFK-2017 Chapter 3 Bus Controller Configuration 3-23
Page 1 and 2: GE Fanuc AutomationProgrammable Con
Page 3 and 4: ContentsChapter 1Introduction......
Page 5 and 6: ContentsFault Table Definitions Ass
Page 7: ContentsMonitoring Inputs..........
Page 10 and 11: 1Related PublicationsFor more infor
Page 12 and 13: 1Bus Controller DescriptionThe Geni
Page 14 and 15: 1Bus Controller OperationThe Bus Co
Page 16 and 17: 1Amount of I/O Data on the BusThe a
Page 18 and 19: 1DatagramsThe Bus Controller suppor
Page 20 and 21: 1Receiving Global DataThe Bus Contr
Page 22 and 23: 2Installing the Bus Controller1. Be
Page 24 and 25: 2Terminating the BusEach Genius com
Page 26 and 27: 3Adding a Bus Controller to the Con
Page 28 and 29: 3Error RateThis entry determines ho
Page 30 and 31: 3Configuring Genius Redundancy on t
Page 32 and 33: 3Dual Bus and Redundant Controller:
Page 34 and 35: 3Using the Redundancy WizardsThe Re
Page 36 and 37: 3Redundancy Wizard: Set up a Primar
Page 38 and 39: 3Redundancy Wizard: Add GBCs for Ge
Page 40 and 41: 34. Click Next.5. Review the settin
Page 42 and 43: 36. Click Next.7. Review the settin
Page 44 and 45: 34. Click Next. Select the rack and
Page 48 and 49: 3Adding Devices to the Bus Configur
Page 50 and 51: 3Reference Address Configuration Ex
Page 52 and 53: 3Reference Address Example Configur
Page 54 and 55: 3ExampleDisabling Outputs for an As
Page 56 and 57: 3Changing a Device's Serial Bus Add
Page 58 and 59: 3Configuring a Remote Bus Controlle
Page 60 and 61: 3Configuring a PowerTRAC Block or H
Page 62 and 63: 3Configuring a Generic Device on th
Page 64 and 65: 3Setting All Bus Devices to Redunda
Page 66 and 67: 3Viewing the Bus Controller Power C
Page 68 and 69: 4System Status ReferencesSystem sta
Page 70 and 71: 4High Alarm and Low Alarm ContactsT
Page 72 and 73: 4Fault Table Definitions Associated
Page 74 and 75: 4Fault Table Definitions Associated
Page 76 and 77: 5Programming for a Communication Re
Page 78 and 79: 5The high byte of address + 2 of th
Page 80 and 81: 5The COMMREQ InstructionAfter suppl
Page 82 and 83: 5COMMREQ Status BlockWhen the Bus C
Page 84 and 85: 5Programming ExamplesThe following
Page 86 and 87: 5COMMREQs and DatagramsThe table be
Page 88 and 89: 5COMMREQ #2: Read Configuration Com
Page 90 and 91: 5COMMREQ #4: Read Diagnostics Comma
Page 92 and 93: 5COMMREQ #7: Assign Monitor Command
Page 94 and 95: 5COMMREQ #8: Enable/Disable Outputs
Page 96 and 97:
5COMMREQ #10: Switch BSM CommandIn
Page 98 and 99:
5Memory Specification for Read Devi
Page 100 and 101:
5Memory Specification: Series Six P
Page 102 and 103:
5COMMREQ #12: Write Device CommandT
Page 104 and 105:
5Number of Dequeue Datagram Command
Page 106 and 107:
5COMMREQ #14: Send Datagram Command
Page 108 and 109:
5Datagram PriorityA Bus Controller
Page 110 and 111:
5COMMREQ #15: Request Datagram Repl
Page 112 and 113:
5COMMREQ #17: Do Output CommandTo i
Page 114 and 115:
5ExampleIn this example, there are
Page 116 and 117:
5COMMREQ #18: Read Serial Bus Addre
Page 118 and 119:
6Reading the Serial Bus Addresses o
Page 120 and 121:
6Series 90-70 CPU: Reading Serial B
Page 122 and 123:
6Series 90-70 CPU: Reading Datagram
Page 124 and 125:
7Data MonitoringIn addition to the
Page 126 and 127:
7RedundancyRedundancy provides extr
Page 128 and 129:
7If, after switching due to loss of
Page 130 and 131:
7Number of Bus Devices on a Dual Bu
Page 132 and 133:
7Redundant ControllersRedundant con
Page 134 and 135:
7Duplex Redundancy ModeIf a bus dev
Page 136 and 137:
7Bus and Controller Redundancy for
Page 138 and 139:
7Operation Remains with Primary PLC
Page 140 and 141:
77-18 Series 90-70 Genius® Bus Con
Page 142 and 143:
A-2 Series 90-70 Genius® Bus Contr
Page 144 and 145:
IndexNumber per CPU Sweep, 5-34Prio
Page 146:
IndexIndex-4 Series 90-70 Genius®
show all

Series 90-70 Genius Bus Controller Manual, GFK-2017

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?