Series 90-70 Genius Bus Controller Manual, GFK-2017

More documents

Recommendations

Info

Chapter1IntroductionThis manual describes the features and operation of a Series 90-70 Genius® BusController when it is used in a PACSystems RX7i or Series 90-70 PLC system. Thismanual also provides the configuration and programming information needed tocomplete the interface between the system CPU and a Genius bus.Product DocumentationContent of this ManualChapter 1. Introduction: Chapter 1 describes the Bus Controller and explains how itoperates.Chapter 2. Installation: Chapter 2 explains how to install or remove a Bus Controller,and how to connect it to a Genius serial bus.Chapter 3. Bus Controller Configuration: Chapter 3 explains how to complete thesoftware configuration steps for a Bus Controller and its bus.Chapter 4. Diagnostics: Chapter 4 describes diagnostics capabilities provided by theBus Controller.Chapter 5. Communication Request: Chapter 5 describes the use of the COMMREQprogram instruction with a Bus Controller.Chapter 6. Reading Bus Status Information: Chapter 6 explains how the applicationprogram can read the Serial Bus Addresses of active devices or read the status of theDatagram queue.Chapter 7. Data Monitoring, Distributed Control, and Redundancy: Chapter 7describes basic types of data monitoring, distributed control and redundancy systemsthat are supported by the Bus Controller.Appendix A. ASCII Code List: Lists ASCII characters and their decimal andhexadecimal equivalents.GFK-2017 1-1
Page 1 and 2: GE Fanuc AutomationProgrammable Con
Page 3 and 4: ContentsChapter 1Introduction......
Page 5 and 6: ContentsFault Table Definitions Ass
Page 7: ContentsMonitoring Inputs..........
Page 11 and 12: 1System OverviewThe Genius Bus Cont
Page 13 and 14: 1The Genius BusThe Genius bus is a
Page 15 and 16: 1Input Data from Devices on the Bus
Page 17 and 18: 1DiagnosticsGenius blocks and other
Page 19 and 20: 1Global DataGlobal Data is data tha
Page 21 and 22: Chapter2InstallationThis chapter ex
Page 23 and 24: 2Connecting the Serial BusFor infor
Page 25 and 26: Chapter3Bus Controller Configuratio
Page 27 and 28: 3Configuring the Bus Controller Set
Page 29 and 30: 3Configuring Global DataSelect the
Page 31 and 32: 3Dual Bus:Select Dual Bus if there
Page 33 and 34: 3Configuring Redundancy ParametersW
Page 35 and 36: 3Redundancy WizardsThe Redundancy w
Page 37 and 38: 33. Choose the CPU type and redunda
Page 39 and 40: 3Add GBCs for Genius Redundancy: Du
Page 41 and 42: 3Add GBCs for Genius Redundancy: Re
Page 43 and 44: 3Add GBCs for Genius Redundancy: Re
Page 45 and 46: 3Add GBCs for Genius Redundancy: Du
Page 47 and 48: 3Redundancy Wizard: Generate Second
Page 49 and 50: 3Configuring the Device Reference A
Page 51 and 52: 3Reference Address Example Configur
Page 53 and 54: 3Disabling OutputsIf outputs are di
Page 55 and 56: 3Bus Device Redundancy Configuratio
Page 57 and 58: 3Configuring a Remote DropEnter or
Page 59 and 60:
3Set Up Global DataIf a Bus Control
Page 61 and 62:
3Configuring Parameters for a High-
Page 63 and 64:
3Copying a Bus ConfigurationTo copy
Page 65 and 66:
3Programmer Configuration of Bus De
Page 67 and 68:
Chapter4DiagnosticsThis chapter des
Page 69 and 70:
4Fault and No Fault ContactsFAULT a
Page 71 and 72:
4Fault Table Definitions for Genius
Page 73 and 74:
4Fault Table Definitions Associated
Page 75 and 76:
Chapter5Communication RequestsThis
Page 77 and 78:
5COMMREQ Command Block FormatThe fi
Page 79 and 80:
5Command Block Quick ReferenceComma
Page 81 and 82:
5COMMREQ Inputs(enable)IN:SYSID:Per
Page 83 and 84:
5Contents of the Status BlockThe St
Page 85 and 86:
5The Move instructions are executed
Page 87 and 88:
5COMMREQ #1: Pulse Test CommandThe
Page 89 and 90:
5COMMREQ #3: Write Configuration Co
Page 91 and 92:
5COMMREQ #5: Clear Circuit Faults C
Page 93 and 94:
5Command Block for the Assign Monit
Page 95 and 96:
5COMMREQ #9: Enable/Disable Global
Page 97 and 98:
5COMMREQ #11: Read Device CommandTo
Page 99 and 100:
5Example A:Example B:For 3 bits sta
Page 101 and 102:
5Example of Read DeviceIn the follo
Page 103 and 104:
5COMMREQ #13: Dequeue Datagram Comm
Page 105 and 106:
5Program logic should be used to as
Page 107 and 108:
5Command Block for the Send Datagra
Page 109 and 110:
5Effect of Datagrams on the Genius
Page 111 and 112:
5COMMREQ #16: Enable/Disable I/O Fa
Page 113 and 114:
5Command Block for the Do Output Co
Page 115 and 116:
5Using the Do Output Command for Gl
Page 117 and 118:
Chapter6Reading Bus Status Informat
Page 119 and 120:
6RX7i CPU: Reading Serial Bus Addre
Page 121 and 122:
6Reading the Status of the Datagram
Page 123 and 124:
Chapter7Data Monitoring, Distribute
Page 125 and 126:
7Distributed ControlDistributed con
Page 127 and 128:
7Dual Bus RedundancyDual busses can
Page 129 and 130:
7During normal operation, both bus
Page 131 and 132:
7Dual Bus with the Bus Controllers
Page 133 and 134:
7Bus Device Configuration: Hot Stan
Page 135 and 136:
7Dual Bus and Redundant Controllers
Page 137 and 138:
7Bus and Controller Redundancy for
Page 139 and 140:
7Genius Redundancy for Series 90-70
Page 141 and 142:
AppendixAASCII Code ListIn Read Dev
Page 143 and 144:
IndexAAD Comm fault, 4-7Add. of Bus
Page 145 and 146:
IndexMemory for Read/Write Device,
show all

Series 90-70 Genius Bus Controller Manual, GFK-2017

Create successful ePaper yourself

Delete template?

Save as template?