Model 7600 - Teledyne Analytical Instruments

More documents

Recommendations

Info

Introduction Model 7600• Biochemistry and fermentation,• Automotive emission analysis• Explosive and toxic gas analysis• Chemical analysis• Refinery operation• Research applications1.5 Description of the Main UnitTeledyne's Series 7600 Infrared Gas Analyzer measures theconcentration of NO, SO 2 , CO 2 , CO, and CH 4 in a gas mixture on acontinuous basis. The Series 7600 can also be supplied with an oxygensensor, which allows the simultaneous measurement of oxygenconcentration as well. The NEMA-4 enclosure can be X or Z-purged tosatisfy hazardous area installation requirements.The system uses a high-sensitivity mass flow type twin detector forinfrared measurements. A single beam, double path optical bench isinstalled in conjunction with a serial dual-layer transmission detector.The concentration of the desired gases is displayed on a large, easyto-readbacklit LCD. The user interface is very intuitive and the menu /mode selection buttons, which are readily accessible, provide theoperator with dynamic control and extensive diagnostic capabilities. SeeFigure 1-2.The front panel mounted power switch turns the instrument on andoff while the display switch controls power to the display.Front panel mounted handles make sliding the instrument out of thepanel rack or enclosure a simple task for easy maintenance.Teledyne Analytical Instruments 18
Infrared Gas AnalyzerIntroductionFigure 1-2: Model 7600 DescriptionGas connections for the 7600 instrument are made on the rear panelof the instrument using the ¼” NPT fittings installed. The standardinstrument has two measuring units and a pair of inlet/outlet gasconnections exist for each unit. See Section 2.5 Gas Connections.A power receptacle on the rear panel accepts the three-prong powercable supplied with the instrument. The Model 7600 operates on 100-240 VAC 50/60 Hz power. The power inlet conforms to EN60320Protection Class 1 specifications.Teledyne Analytical Instruments 19
Page 1: OPERATING INSTRUCTIONS FORModel 760
Page 5 and 6: Infrared Gas AnalyzerIF YOU USE THE
Page 7: Infrared Gas AnalyzerOperation ....
Page 10 and 11: Model 7600List of FiguresFigure 1-1
Page 12 and 13: Model 7600List of TablesTable 2-1:
Page 14 and 15: Model 7600Teledyne Analytical Instr
Page 16 and 17: Introduction Model 7600Figure 1-1:
Page 20 and 21: Introduction Model 7600Teledyne Ana
Page 22 and 23: Installation Model 7600* These opti
Page 24 and 25: Installation Model 7600mounting sur
Page 26 and 27: Installation Model 7600An internal
Page 28 and 29: Installation Model 7600Figure 2-6:
Page 30 and 31: Installation Model 76002.5.6 Purgin
Page 32 and 33: Installation Model 76002.6 Electric
Page 34 and 35: Installation Model 76002.7 Testing
Page 36 and 37: Operation Model 7600MODE key:LEFT/R
Page 38 and 39: Operation Model 7600The user mode i
Page 40 and 41: Operation Model 7600Where:On: The v
Page 42 and 43: Operation Model 7600• Set up the
Page 44 and 45: Operation Model 76002. Move the hig
Page 46 and 47: Operation Model 76003.5.1.4 AUTORAN
Page 48 and 49: Operation Model 7600Note: Enter set
Page 50 and 51: Operation Model 7600zero calibratio
Page 52 and 53: Operation Model 7600(AR), it will b
Page 54 and 55: Operation Model 7600• High Limit:
Page 56 and 57: Operation Model 76004. The alarm it
Page 58 and 59: Operation Model 7600To close the
Page 60 and 61: Operation Model 7600To set the flow
Page 62 and 63: Operation Model 7600When a channel
Page 64 and 65: Operation Model 76005. From the mea
Page 66 and 67: Operation Model 76003. In the “Se
Page 68 and 69:
Operation Model 76003.5.5.2 FORCED
Page 70 and 71:
Operation Model 7600Note: During au
Page 72 and 73:
Operation Model 7600Hysteresis:Sett
Page 74 and 75:
Operation Model 7600Reset Av. Outpu
Page 76 and 77:
Operation Model 7600Auto calibratio
Page 78 and 79:
Operation Model 76005. On the param
Page 80 and 81:
Operation Model 7600To modify the a
Page 82 and 83:
Operation Model 76002. Select Param
Page 84 and 85:
Operation Model 7600CO M: CO sensor
Page 86 and 87:
Operation Model 76003.6.5 Moisture
Page 88 and 89:
Operation Model 7600• Station No.
Page 90 and 91:
Operation Model 76003.7 Calibration
Page 92 and 93:
Operation Model 7600To close "Span
Page 94 and 95:
Maintenance Model 7600Item to beche
Page 96 and 97:
Maintenance Model 7600Figure 4-3: S
Page 98 and 99:
Maintenance Model 7600Figure 4-5: D
Page 100 and 101:
Maintenance Model 7600introduced di
Page 102 and 103:
Maintenance Model 7600Figure 4-9: B
Page 104 and 105:
Maintenance Model 7600close to 0 as
Page 106 and 107:
Maintenance Model 7600Pressing ENT
Page 108 and 109:
Maintenance Model 7600Teledyne Anal
Page 110 and 111:
Appendix Model 7600Analog Output: 1
Page 112 and 113:
Appendix Model 7600Range switching:
Page 114 and 115:
Appendix Model 7600Upper/lower limi
Page 116 and 117:
Appendix Model 7600CO concentration
Page 118 and 119:
Appendix Model 7600A.6 Installation
Page 120 and 121:
Appendix Model 7600A.9 Description
Page 122 and 123:
Appendix Model 7600Teledyne Analyti
Page 124 and 125:
Appendix Model 7600Teledyne Analyti
Page 126:
Index Model 7600Teledyne Analytical
show all

Model 7600 - Teledyne Analytical Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?