Model 7600 - Teledyne Analytical Instruments

More documents

Recommendations

Info

Operation Model 76002. Move the highlight of the cursor to range selection andselect the desired range using the UP/DOWN keys. Thehighlighted arrow indicates the currently selected range.3. Press ENT to accept the selection. Measurement is nowcarried out using the selected range.Note: If “RR” or “AR” is selected as range switch mode, manualrange selection as described above is not possibleThe range for O 2 correction value, O 2 correction averagevalue, and O 2 average value is automatically switched ifthe corresponding instantaneous value range is switched.To abort the range selection, press the ESC key and the settingoperation is made invalid and the previous screen appears.3.5.1.2 RANGE IDENTIFICATION CONTACT OPERATIONIn all of the range switch modes (MR, RR, AR), the status of therange identification relay contact corresponding to each Ch (component)is closed when Range 1 is selected, and open when Range 2 is selected.Note that even if the range is switched while a hold of measurementis in place, for instance, by a remote hold contact input or the hold ofmeasurement value during calibration, the range identification contactmaintains the contact state immediately before the hold. After stop of thehold, the contact state of the current range is resumed.Teledyne Analytical Instruments 44
Infrared Gas AnalyzerOperation3.5.1.3 REMOTE RANGE SELECTIONThe range can be selected remotely if a remote switch has beeninstalled. To use this feature, the range mode must be switched in thedisplay to RR (Remote Range) .To configure the instrument for remote range selection:1. Press the MODE key to enter the user mode.2. Move the cursor to the “Switch Ranges” option and pressENT. The “Channel Selection” screen appears.3. Move the cursor by pressing the UP/DOWN keys to thedesired channel and press ENT.The selected range switch mode is highlighted for the channel youselected.4. Press the UP/DOWN keys to toggle between theavailable switch modes until RR is displayed.5. Press the ENT key to accept the selection.Teledyne Analytical Instruments 45
Page 1: OPERATING INSTRUCTIONS FORModel 760
Page 5 and 6: Infrared Gas AnalyzerIF YOU USE THE
Page 7: Infrared Gas AnalyzerOperation ....
Page 10 and 11: Model 7600List of FiguresFigure 1-1
Page 12 and 13: Model 7600List of TablesTable 2-1:
Page 14 and 15: Model 7600Teledyne Analytical Instr
Page 16 and 17: Introduction Model 7600Figure 1-1:
Page 18 and 19: Introduction Model 7600• Biochemi
Page 20 and 21: Introduction Model 7600Teledyne Ana
Page 22 and 23: Installation Model 7600* These opti
Page 24 and 25: Installation Model 7600mounting sur
Page 26 and 27: Installation Model 7600An internal
Page 28 and 29: Installation Model 7600Figure 2-6:
Page 30 and 31: Installation Model 76002.5.6 Purgin
Page 32 and 33: Installation Model 76002.6 Electric
Page 34 and 35: Installation Model 76002.7 Testing
Page 36 and 37: Operation Model 7600MODE key:LEFT/R
Page 38 and 39: Operation Model 7600The user mode i
Page 40 and 41: Operation Model 7600Where:On: The v
Page 42 and 43: Operation Model 7600• Set up the
Page 46 and 47: Operation Model 76003.5.1.4 AUTORAN
Page 48 and 49: Operation Model 7600Note: Enter set
Page 50 and 51: Operation Model 7600zero calibratio
Page 52 and 53: Operation Model 7600(AR), it will b
Page 54 and 55: Operation Model 7600• High Limit:
Page 56 and 57: Operation Model 76004. The alarm it
Page 58 and 59: Operation Model 7600To close the
Page 60 and 61: Operation Model 7600To set the flow
Page 62 and 63: Operation Model 7600When a channel
Page 64 and 65: Operation Model 76005. From the mea
Page 66 and 67: Operation Model 76003. In the “Se
Page 68 and 69: Operation Model 76003.5.5.2 FORCED
Page 70 and 71: Operation Model 7600Note: During au
Page 72 and 73: Operation Model 7600Hysteresis:Sett
Page 74 and 75: Operation Model 7600Reset Av. Outpu
Page 76 and 77: Operation Model 7600Auto calibratio
Page 78 and 79: Operation Model 76005. On the param
Page 80 and 81: Operation Model 7600To modify the a
Page 82 and 83: Operation Model 76002. Select Param
Page 84 and 85: Operation Model 7600CO M: CO sensor
Page 86 and 87: Operation Model 76003.6.5 Moisture
Page 88 and 89: Operation Model 7600• Station No.
Page 90 and 91: Operation Model 76003.7 Calibration
Page 92 and 93: Operation Model 7600To close "Span
Page 94 and 95:
Maintenance Model 7600Item to beche
Page 96 and 97:
Maintenance Model 7600Figure 4-3: S
Page 98 and 99:
Maintenance Model 7600Figure 4-5: D
Page 100 and 101:
Maintenance Model 7600introduced di
Page 102 and 103:
Maintenance Model 7600Figure 4-9: B
Page 104 and 105:
Maintenance Model 7600close to 0 as
Page 106 and 107:
Maintenance Model 7600Pressing ENT
Page 108 and 109:
Maintenance Model 7600Teledyne Anal
Page 110 and 111:
Appendix Model 7600Analog Output: 1
Page 112 and 113:
Appendix Model 7600Range switching:
Page 114 and 115:
Appendix Model 7600Upper/lower limi
Page 116 and 117:
Appendix Model 7600CO concentration
Page 118 and 119:
Appendix Model 7600A.6 Installation
Page 120 and 121:
Appendix Model 7600A.9 Description
Page 122 and 123:
Appendix Model 7600Teledyne Analyti
Page 124 and 125:
Appendix Model 7600Teledyne Analyti
Page 126:
Index Model 7600Teledyne Analytical
show all

Model 7600 - Teledyne Analytical Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?