Model 7600 - Teledyne Analytical Instruments

More documents

Recommendations

Info

Installation Model 7600An internal piping diagram for an instrument with one or twomeasuring units is shown in Figure 2-4. When there are two measuringunits, if a built-in oxygen sensor is used, it must be installed inmeasuring unit 2. The diagram shows the combination of two cells usedin measuring unit #2. This is possible by combining ranges. When asingle measuring unit is used, there is only a single inlet and outlet gasconnection.Figure 2-4: Internal Piping with Single or Dual Measuring UnitsDepending on the options chosen, the analyzer can be configured inseveral ways. Table 2-1 lists the possible configurations for single anddual measuring units with 1 to 4 component meters.Teledyne Analytical Instruments 26
Infrared Gas AnalyzerInstallationTable 2-1: Correspondence of Measured Components and MeasuringUnitsMeasuring components Measuring unit 1 Measuring unit 21-component meter for NO,SO 2 , CO 2 , CO and CH 42-component meter forNO/SO 2 and CO 2 /CO2-component meter forNO/CO3-component meter forNO/SO 2 /CO4-component meter forNO/SO 2 /CO 2 /COEach componentNO/SO 2CO 2 /CONONO/SO 2NO/SO 2NoneNoneCOCOCO 2 /CO2.5.2 External Piping DiagramThere are several ways to bring sample gas to the analyzerdepending on the number of inlet/outlet gas connections on yourinstrument Recommended piping diagrams are shown in Figures 2-5, 2-6 and 2-7. Figure 2-5 is a schematic for an instrument with a single pairof inlet/outlet gas connections. Figures 2-6 and 2-7 are used when thereare two pair of inlet/outlet connections. Note that a NO 2 /NO converteris used when NO measurement is used for NOx analysis.Figure 2-5: External Piping with Single Inlet and OutletTeledyne Analytical Instruments 27
Page 1: OPERATING INSTRUCTIONS FORModel 760
Page 5 and 6: Infrared Gas AnalyzerIF YOU USE THE
Page 7: Infrared Gas AnalyzerOperation ....
Page 10 and 11: Model 7600List of FiguresFigure 1-1
Page 12 and 13: Model 7600List of TablesTable 2-1:
Page 14 and 15: Model 7600Teledyne Analytical Instr
Page 16 and 17: Introduction Model 7600Figure 1-1:
Page 18 and 19: Introduction Model 7600• Biochemi
Page 20 and 21: Introduction Model 7600Teledyne Ana
Page 22 and 23: Installation Model 7600* These opti
Page 24 and 25: Installation Model 7600mounting sur
Page 28 and 29: Installation Model 7600Figure 2-6:
Page 30 and 31: Installation Model 76002.5.6 Purgin
Page 32 and 33: Installation Model 76002.6 Electric
Page 34 and 35: Installation Model 76002.7 Testing
Page 36 and 37: Operation Model 7600MODE key:LEFT/R
Page 38 and 39: Operation Model 7600The user mode i
Page 40 and 41: Operation Model 7600Where:On: The v
Page 42 and 43: Operation Model 7600• Set up the
Page 44 and 45: Operation Model 76002. Move the hig
Page 46 and 47: Operation Model 76003.5.1.4 AUTORAN
Page 48 and 49: Operation Model 7600Note: Enter set
Page 50 and 51: Operation Model 7600zero calibratio
Page 52 and 53: Operation Model 7600(AR), it will b
Page 54 and 55: Operation Model 7600• High Limit:
Page 56 and 57: Operation Model 76004. The alarm it
Page 58 and 59: Operation Model 7600To close the
Page 60 and 61: Operation Model 7600To set the flow
Page 62 and 63: Operation Model 7600When a channel
Page 64 and 65: Operation Model 76005. From the mea
Page 66 and 67: Operation Model 76003. In the “Se
Page 68 and 69: Operation Model 76003.5.5.2 FORCED
Page 70 and 71: Operation Model 7600Note: During au
Page 72 and 73: Operation Model 7600Hysteresis:Sett
Page 74 and 75: Operation Model 7600Reset Av. Outpu
Page 76 and 77:
Operation Model 7600Auto calibratio
Page 78 and 79:
Operation Model 76005. On the param
Page 80 and 81:
Operation Model 7600To modify the a
Page 82 and 83:
Operation Model 76002. Select Param
Page 84 and 85:
Operation Model 7600CO M: CO sensor
Page 86 and 87:
Operation Model 76003.6.5 Moisture
Page 88 and 89:
Operation Model 7600• Station No.
Page 90 and 91:
Operation Model 76003.7 Calibration
Page 92 and 93:
Operation Model 7600To close "Span
Page 94 and 95:
Maintenance Model 7600Item to beche
Page 96 and 97:
Maintenance Model 7600Figure 4-3: S
Page 98 and 99:
Maintenance Model 7600Figure 4-5: D
Page 100 and 101:
Maintenance Model 7600introduced di
Page 102 and 103:
Maintenance Model 7600Figure 4-9: B
Page 104 and 105:
Maintenance Model 7600close to 0 as
Page 106 and 107:
Maintenance Model 7600Pressing ENT
Page 108 and 109:
Maintenance Model 7600Teledyne Anal
Page 110 and 111:
Appendix Model 7600Analog Output: 1
Page 112 and 113:
Appendix Model 7600Range switching:
Page 114 and 115:
Appendix Model 7600Upper/lower limi
Page 116 and 117:
Appendix Model 7600CO concentration
Page 118 and 119:
Appendix Model 7600A.6 Installation
Page 120 and 121:
Appendix Model 7600A.9 Description
Page 122 and 123:
Appendix Model 7600Teledyne Analyti
Page 124 and 125:
Appendix Model 7600Teledyne Analyti
Page 126:
Index Model 7600Teledyne Analytical
show all

Model 7600 - Teledyne Analytical Instruments

Create successful ePaper yourself

Delete template?

Save as template?