Model 7600 - Teledyne Analytical Instruments

More documents

Recommendations

Info

Operation Model 76003.5.1.4 AUTORANGINGThe Model 7600 can be set to autorange where the instrument willselect the analysis range automatically. To use the autorange feature, ARmust be selected for the switch mode. Note that each channel isindependent so that autoranging can be used for some or all of theavailable channels. the remaining channels can be configured to manualor remote switching.To setup autoranging use the same procedure as Section 3.5.1.1except you must select AR for the switch mode on the channel orchannels you want to autorange.3.5.2 Calibration ParametersThe next menu choice from the user screen is the CalibrationParameters menu. Here calibration settings can be configured for yourparticular application. There are 4 submenus in the CalibrationParameters menu. They are:• Calibration Value—set the concentration of calibration gas• About ZERO Calibration—set each or all components to bezero calibrated during a manual zero calibration.• About Calibration Range—sets whether each componentduring a zero or span calibration should be calibrated with asingle or dual range.• Auto Calibration Components/Range— select the componentand range with which auto calibration is to be performed.3.5.2.1 CALIBRATION VALUEThis submenu allows you to set the concentration of the standardgas (zero and span) for each channel used for calibration.To enter the Calibration Value submenu:1. From measurement mode, press the MODE key todisplay the user mode.2. Point the cursor to “Calibration Parameters” by pressingthe UP or DOWN key.3. Press the ENT key to enter the Calibration Parametersmenu.Teledyne Analytical Instruments 46
Infrared Gas AnalyzerOperation4. In the “Calibration Parameters” screen that appears, pointthe cursor to “Calibration Value” by pressing the UP orDOWN key. Press the ENT key.To change the concentration of a calibration gas:1. Point the cursor to the channel you want to set by usingthe UP or DOWN key. Press the ENT key.2. Select the concentration item you want to set by pressingthe UP or DOWN or SIDE key. Press the ENT key, andthe selected value is highlighted.3. Enter the calibration gas concentration values (zero andspan). For any numerical value entry, press the UP orDOWN key to increase or decrease a single digit. Selectthe next digit by pressing the SIDE key.4. When the concentration is correct, save the entry bypressing the ENT key. The saved value becomes validfrom the next calibration process.Teledyne Analytical Instruments 47
Page 1: OPERATING INSTRUCTIONS FORModel 760
Page 5 and 6: Infrared Gas AnalyzerIF YOU USE THE
Page 7: Infrared Gas AnalyzerOperation ....
Page 10 and 11: Model 7600List of FiguresFigure 1-1
Page 12 and 13: Model 7600List of TablesTable 2-1:
Page 14 and 15: Model 7600Teledyne Analytical Instr
Page 16 and 17: Introduction Model 7600Figure 1-1:
Page 18 and 19: Introduction Model 7600• Biochemi
Page 20 and 21: Introduction Model 7600Teledyne Ana
Page 22 and 23: Installation Model 7600* These opti
Page 24 and 25: Installation Model 7600mounting sur
Page 26 and 27: Installation Model 7600An internal
Page 28 and 29: Installation Model 7600Figure 2-6:
Page 30 and 31: Installation Model 76002.5.6 Purgin
Page 32 and 33: Installation Model 76002.6 Electric
Page 34 and 35: Installation Model 76002.7 Testing
Page 36 and 37: Operation Model 7600MODE key:LEFT/R
Page 38 and 39: Operation Model 7600The user mode i
Page 40 and 41: Operation Model 7600Where:On: The v
Page 42 and 43: Operation Model 7600• Set up the
Page 44 and 45: Operation Model 76002. Move the hig
Page 48 and 49: Operation Model 7600Note: Enter set
Page 50 and 51: Operation Model 7600zero calibratio
Page 52 and 53: Operation Model 7600(AR), it will b
Page 54 and 55: Operation Model 7600• High Limit:
Page 56 and 57: Operation Model 76004. The alarm it
Page 58 and 59: Operation Model 7600To close the
Page 60 and 61: Operation Model 7600To set the flow
Page 62 and 63: Operation Model 7600When a channel
Page 64 and 65: Operation Model 76005. From the mea
Page 66 and 67: Operation Model 76003. In the “Se
Page 68 and 69: Operation Model 76003.5.5.2 FORCED
Page 70 and 71: Operation Model 7600Note: During au
Page 72 and 73: Operation Model 7600Hysteresis:Sett
Page 74 and 75: Operation Model 7600Reset Av. Outpu
Page 76 and 77: Operation Model 7600Auto calibratio
Page 78 and 79: Operation Model 76005. On the param
Page 80 and 81: Operation Model 7600To modify the a
Page 82 and 83: Operation Model 76002. Select Param
Page 84 and 85: Operation Model 7600CO M: CO sensor
Page 86 and 87: Operation Model 76003.6.5 Moisture
Page 88 and 89: Operation Model 7600• Station No.
Page 90 and 91: Operation Model 76003.7 Calibration
Page 92 and 93: Operation Model 7600To close "Span
Page 94 and 95: Maintenance Model 7600Item to beche
Page 96 and 97:
Maintenance Model 7600Figure 4-3: S
Page 98 and 99:
Maintenance Model 7600Figure 4-5: D
Page 100 and 101:
Maintenance Model 7600introduced di
Page 102 and 103:
Maintenance Model 7600Figure 4-9: B
Page 104 and 105:
Maintenance Model 7600close to 0 as
Page 106 and 107:
Maintenance Model 7600Pressing ENT
Page 108 and 109:
Maintenance Model 7600Teledyne Anal
Page 110 and 111:
Appendix Model 7600Analog Output: 1
Page 112 and 113:
Appendix Model 7600Range switching:
Page 114 and 115:
Appendix Model 7600Upper/lower limi
Page 116 and 117:
Appendix Model 7600CO concentration
Page 118 and 119:
Appendix Model 7600A.6 Installation
Page 120 and 121:
Appendix Model 7600A.9 Description
Page 122 and 123:
Appendix Model 7600Teledyne Analyti
Page 124 and 125:
Appendix Model 7600Teledyne Analyti
Page 126:
Index Model 7600Teledyne Analytical
show all

Model 7600 - Teledyne Analytical Instruments

Create successful ePaper yourself

Delete template?

Save as template?