LPS Instruction Manual - HygroMatik

More documents

Recommendations

Info

4.2.4 Atomising nozzlesDesalinated water at a pressure of up to 16 bar reaches the nozzleswhere the water is atomised to form ultra-fine mist-like aerosols.The aerosols enter the area of the vortexed air streamdownstream of the vortex modules. The air and aerosols aremixed intensively here.The atomising nozzle generates a spray cone with a wide openingangle.211: Nozzle opening2: Nozzle bodyFunctioning:The nozzle sets the flowing water in rotation and thereby it canleave at high speed. This enables a very fine water spray. Thehigher the operating pressure, the finer the droplets.Material of the nozzle: corrosion-free stainless steelPage 14
4.2.5 Droplet separators (optional)droplet separatorsThere are no more atomised water droplets in the air streambehind the HygroMatik LPS nozzle system (if the environmentalparameter specifications are complied with). The two wire-meshdroplet separators arranged in series ensure this. The trap padsexhibit a low pressure drop (75 Pa at air velocity of 2.0 m/s andaverage air density of 1.2 kg/m³).The air velocity should be between 0.9 m/s and 2.8 m/s. If it isoutside this range it can cause moisture breakthrough downstreamof the droplet separators - in such cases please first contactHygroMatik.The droplet separators are inserted into the humidificationchamber via guide rails and are hence easy to remove for servicing.The traps are standardly delivered with corrosion-resistant metalframes.Note: Hygiene compliance checks applies only to systems withdroplet separators.4.2.6 Humidification sectionThe section between the vortex module wall and the droplet separatorsis called the 'humidification section' in this system. It isunobstructed and hence easy to monitor and clean.For a total standard installation length of 1.5 m for the HygroMatikLPS nozzle system the humidification section should have alength of at least 0.9 m. The exact dimensions are described inthe schematic in the section entitled 'Overview of the humidificationchamber'.Page 15
Page 1 and 2: Operating manualLPSHumidifies and C
Page 3 and 4: 1. Introduction ...................
Page 5 and 6: 1. IntroductionDear Customer,Thank
Page 7 and 8: Exemptions of usage:The HygroMatik
Page 9 and 10: Supervise children in order to ensu
Page 11 and 12: 4. Function and design4.1 Functioni
Page 13: 4.2.3 Vortex modulesThe vortex modu
Page 17 and 18: 5. Connnections5.1 WaterConnection:
Page 19 and 20: 6. Interfaces to the HygroMatik noz
Page 21 and 22: 7. Mechanical assemblyCaution: The
Page 23 and 24: 7.3.2 Examplary design of guide rai
Page 25 and 26: 7.4 Installation of the nozzles, di
Page 27 and 28: 7.4.3 PipingManifold - Nozzles» Th
Page 29 and 30: Assembly of the hose guide» Drill
Page 31 and 32: » Check by gently pulling the tube
Page 33 and 34: Dimensions of guide rails for dropl
Page 35 and 36: 7.6 Pump station wall mountingThe i
Page 37 and 38: 8. Dimensions - Pump StationView fr
Page 39 and 40: Note: There must be a stopcock and
Page 41 and 42: 9.4 Water QualityConductivity:5-20
Page 43 and 44: 11. Electrical connectionCaution: V
Page 45 and 46: 11.3 Circuit diagramUVWNL3215.09.20
Page 47 and 48: 11.4 Inspecting the electrical inst
Page 49 and 50: 13. MaintenanceThe HygroMatik nozzl
Page 51 and 52: 1. Set the main switch on the contr
Page 53 and 54: 13.1.5 Cleaning the humidification
Page 55 and 56: 14.1.1 Full load and part loadThe H
Page 57 and 58: Functional description of the displ
Page 59 and 60: 14.2.2.1 Reading level:The followin
Page 61 and 62: 14.2.3 Overview of error reportsFau
Page 63 and 64: 15. EC declaration of conformityPag
Page 65 and 66:
Artikel-Nr. Article no. Vortex-wall
Page 67 and 68:
18. Technical SpecificationsLPS 45
Page 69 and 70:
43Page 69
show all

LPS Instruction Manual - HygroMatik

Create successful ePaper yourself

Delete template?

Save as template?