LPS Instruction Manual - HygroMatik

More documents

Recommendations

Info

7.5 Assembling the droplet separatorsThe guide rails must be installed in a way that makes it possibleto either pull out or lift up the vortex module wall.Detail BDetail A7.5.1 Examplary design of guide rails for the dropletseparatorsDetail A:Dimensions given in mmA1: Trap guide rail: U-section with perforated 1.4301 stainlesssteel sheetA2: Trap guide rail holder: U-section made from 1.4301 stainlesssteelA3: Several holes (at least 4 per metre) 8-10 mm in diameterdistributed over the length of the trap holderA4: Collection tray for humidification chamberA5: Fixation of guide rail with the floor of the humidificationchamber (ensure that condensate can freely run to the drain)Page 32
Dimensions of guide rails for droplet separatorsMaterial used for upper guide rail: 1.4301 stainless steel sheet,thickness: 1 mmDetail B:Hight is variabel:pushed in dropletseparators: 55lifted in dropletseparatosr: 30The upper guide rail is directly attache to the ceiling of thehumidification chamber (using screws, rivets or similar)Assembling two droplet separators in a stackFor installation heights of above 1.5 m, two droplet separatorsmust be mounted in a stack.The waste water from the upper droplet separator is drained viaan additional collector. For this the waste water from the uppertrap is drained via a flexible hose either directly or into the collectiontray. This additional collector is to be provided for both thepreliminary and the final droplet separator.1. Upper guide rail2. Detail C (please see nextpage)3. Lower guide railPage 33
Page 1 and 2: Operating manualLPSHumidifies and C
Page 3 and 4: 1. Introduction ...................
Page 5 and 6: 1. IntroductionDear Customer,Thank
Page 7 and 8: Exemptions of usage:The HygroMatik
Page 9 and 10: Supervise children in order to ensu
Page 11 and 12: 4. Function and design4.1 Functioni
Page 13 and 14: 4.2.3 Vortex modulesThe vortex modu
Page 15 and 16: 4.2.5 Droplet separators (optional)
Page 17 and 18: 5. Connnections5.1 WaterConnection:
Page 19 and 20: 6. Interfaces to the HygroMatik noz
Page 21 and 22: 7. Mechanical assemblyCaution: The
Page 23 and 24: 7.3.2 Examplary design of guide rai
Page 25 and 26: 7.4 Installation of the nozzles, di
Page 27 and 28: 7.4.3 PipingManifold - Nozzles» Th
Page 29 and 30: Assembly of the hose guide» Drill
Page 31: » Check by gently pulling the tube
Page 35 and 36: 7.6 Pump station wall mountingThe i
Page 37 and 38: 8. Dimensions - Pump StationView fr
Page 39 and 40: Note: There must be a stopcock and
Page 41 and 42: 9.4 Water QualityConductivity:5-20
Page 43 and 44: 11. Electrical connectionCaution: V
Page 45 and 46: 11.3 Circuit diagramUVWNL3215.09.20
Page 47 and 48: 11.4 Inspecting the electrical inst
Page 49 and 50: 13. MaintenanceThe HygroMatik nozzl
Page 51 and 52: 1. Set the main switch on the contr
Page 53 and 54: 13.1.5 Cleaning the humidification
Page 55 and 56: 14.1.1 Full load and part loadThe H
Page 57 and 58: Functional description of the displ
Page 59 and 60: 14.2.2.1 Reading level:The followin
Page 61 and 62: 14.2.3 Overview of error reportsFau
Page 63 and 64: 15. EC declaration of conformityPag
Page 65 and 66: Artikel-Nr. Article no. Vortex-wall
Page 67 and 68: 18. Technical SpecificationsLPS 45
Page 69 and 70: 43Page 69

LPS Instruction Manual - HygroMatik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?