LPS Instruction Manual - HygroMatik

More documents

Recommendations

Info

5.4 ElectricalPower supply:External control signal:System enabling:Collective fault signal:Operating status signal:LNE 230 V AC, 50 Hz (a fixedsocket (16 A) at the installationsite is necessary)0-10 V DC4-20 mA DCvia ext. potential-free contactpotential-free contact (changeover contact)potential-free contact (NO)Page 18
6. Interfaces to the HygroMatik nozzle systemLPS6.1 AirAir purity:A Class F7 pre-filter is to beplaced upstream of the HygroMatik nozzle system LPS.Air velocity:0.9-2.8* m/sIf the air velocity is outside this range please contact HygroMatik.(*: under ideal conditions)Pressure drop:Approx. 80 Pa (at an air velocityof 2.0 m/s and with use of a vortex module wall and two drydroplet separators).Air volume flow (for 'partial-load / full-load switching'option):If the HygroMatik nozzle system LPS is operated in systems withmodifiable air volume flows (reduced air volume of less than70% of the maximum air volume), the full-load solenoid valve isswitched off and the partial-load mode is activated. This alsoapplies for systems with multi-stage ventilators.Note: For humidification of rooms the humidified air must exhibita purity in terms of bacterial count in accordance with VDI 6022.6.2 Humidification chamberThe humidification component should be designed with a floortray that has an inclination of at least 1.5° towards the trap andto be waterproof.The water drain must be at the end of the humidification section.The ideal humificiation section length (distance between vortexmodule wall and droplet separators) is 0.9 m. This correspondsto a total installation length of 1.5 m (see schematic in sectionentitled 'Overview of the humidification chamber'). Should thisinstallation length not be available please contact HygroMatik.The humidification chamber should be aerosol-tight and itshould be able to withstand desalinated water.Note: The guide rails for the vortex module wall and droplet separatorsare supplied by the manufacturer. The guide rails mustalready be installed for the system to be started. The vortexmodule wall and droplet separators must also already beinstalled.Page 19
Page 1 and 2: Operating manualLPSHumidifies and C
Page 3 and 4: 1. Introduction ...................
Page 5 and 6: 1. IntroductionDear Customer,Thank
Page 7 and 8: Exemptions of usage:The HygroMatik
Page 9 and 10: Supervise children in order to ensu
Page 11 and 12: 4. Function and design4.1 Functioni
Page 13 and 14: 4.2.3 Vortex modulesThe vortex modu
Page 15 and 16: 4.2.5 Droplet separators (optional)
Page 17: 5. Connnections5.1 WaterConnection:
Page 21 and 22: 7. Mechanical assemblyCaution: The
Page 23 and 24: 7.3.2 Examplary design of guide rai
Page 25 and 26: 7.4 Installation of the nozzles, di
Page 27 and 28: 7.4.3 PipingManifold - Nozzles» Th
Page 29 and 30: Assembly of the hose guide» Drill
Page 31 and 32: » Check by gently pulling the tube
Page 33 and 34: Dimensions of guide rails for dropl
Page 35 and 36: 7.6 Pump station wall mountingThe i
Page 37 and 38: 8. Dimensions - Pump StationView fr
Page 39 and 40: Note: There must be a stopcock and
Page 41 and 42: 9.4 Water QualityConductivity:5-20
Page 43 and 44: 11. Electrical connectionCaution: V
Page 45 and 46: 11.3 Circuit diagramUVWNL3215.09.20
Page 47 and 48: 11.4 Inspecting the electrical inst
Page 49 and 50: 13. MaintenanceThe HygroMatik nozzl
Page 51 and 52: 1. Set the main switch on the contr
Page 53 and 54: 13.1.5 Cleaning the humidification
Page 55 and 56: 14.1.1 Full load and part loadThe H
Page 57 and 58: Functional description of the displ
Page 59 and 60: 14.2.2.1 Reading level:The followin
Page 61 and 62: 14.2.3 Overview of error reportsFau
Page 63 and 64: 15. EC declaration of conformityPag
Page 65 and 66: Artikel-Nr. Article no. Vortex-wall
Page 67 and 68: 18. Technical SpecificationsLPS 45
Page 69 and 70:
43Page 69
show all

LPS Instruction Manual - HygroMatik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?