LPS Instruction Manual - HygroMatik

More documents

Recommendations

Info

Detail C (side view):B1: Preliminary droplet separatorB2: Final droplet separatorB3: Angle bracketB4: Hose connection for drainage of waste water from upperdroplet separatorPerforated sheet metal (material: 1.4301) should be used for thelower guide rails for the droplet separators. Alternatively, sheetmetal with several holes (at least 4 per metre) 8-10 mm in diametercan be used.The assembly must be made with 1.5% incline.Page 34
7.6 Pump station wall mountingThe installation of this unit must be carried out only by qualifiedpersonnel. We can assume no liability for damages caused byincorrect installation.Please observe all the safety instructions and warnings on theequipment.On the rear wall of the unit housing there are 4 mounting brackets(see also: Dimensions, pump station). There is a mountingkit supplied in which four screws, and rawlplugs are included forhanging the unit housing.Firstly, holes are to bedrilled according to thepump station dimensions(see pump station dimensions).Press rawlplugsinto the drilled holes ifdealing with stone or concretewalls. Then screwthe top two fittings to thewall (allowing a 12mmdistance from the screwhead to the wall) andhang up the pump station.Then attach and tightenthe bottom two screws.Hanging tabNote: If installing the system is done by a single person there isa danger that the unit can be dropped. Therefore we recommendthat two qualified persons do the installation.Page 35
Page 1 and 2: Operating manualLPSHumidifies and C
Page 3 and 4: 1. Introduction ...................
Page 5 and 6: 1. IntroductionDear Customer,Thank
Page 7 and 8: Exemptions of usage:The HygroMatik
Page 9 and 10: Supervise children in order to ensu
Page 11 and 12: 4. Function and design4.1 Functioni
Page 13 and 14: 4.2.3 Vortex modulesThe vortex modu
Page 15 and 16: 4.2.5 Droplet separators (optional)
Page 17 and 18: 5. Connnections5.1 WaterConnection:
Page 19 and 20: 6. Interfaces to the HygroMatik noz
Page 21 and 22: 7. Mechanical assemblyCaution: The
Page 23 and 24: 7.3.2 Examplary design of guide rai
Page 25 and 26: 7.4 Installation of the nozzles, di
Page 27 and 28: 7.4.3 PipingManifold - Nozzles» Th
Page 29 and 30: Assembly of the hose guide» Drill
Page 31 and 32: » Check by gently pulling the tube
Page 33: Dimensions of guide rails for dropl
Page 37 and 38: 8. Dimensions - Pump StationView fr
Page 39 and 40: Note: There must be a stopcock and
Page 41 and 42: 9.4 Water QualityConductivity:5-20
Page 43 and 44: 11. Electrical connectionCaution: V
Page 45 and 46: 11.3 Circuit diagramUVWNL3215.09.20
Page 47 and 48: 11.4 Inspecting the electrical inst
Page 49 and 50: 13. MaintenanceThe HygroMatik nozzl
Page 51 and 52: 1. Set the main switch on the contr
Page 53 and 54: 13.1.5 Cleaning the humidification
Page 55 and 56: 14.1.1 Full load and part loadThe H
Page 57 and 58: Functional description of the displ
Page 59 and 60: 14.2.2.1 Reading level:The followin
Page 61 and 62: 14.2.3 Overview of error reportsFau
Page 63 and 64: 15. EC declaration of conformityPag
Page 65 and 66: Artikel-Nr. Article no. Vortex-wall
Page 67 and 68: 18. Technical SpecificationsLPS 45
Page 69 and 70: 43Page 69

LPS Instruction Manual - HygroMatik

Create successful ePaper yourself

Delete template?

Save as template?