User Manual Micro-Calâ¢ Model 869 - Dipl.ing. Houm AS

More documents

Recommendations

Info

$Abbemat Refractometer Se$

ENGINEERING UNITS SCREENThis page is used to convert the displayed engineering units on thePocket PC. All values are stored as a default in WC. Displayed valuesare then converted using conversion values below.Press to set units topresently selectedPress to exit w/outchanging unitsUnits SelectorRadio ButtonsDiagram 20Conversions:Unit Abbr. Unit Name inWC Value Unit ValueinWC Inches Water Column 1.0 1.0cmWC Centimeters Water Column 1.0 2.54Pa Pascal 1.0 248.6491kPa KiloPascal 1.0 0.2486491mbar Millibar 1.0 2.48649130
7.0 UNIT UNDER TEST CONNECTIONSTANDARD 869 - (See Diagram 22)1. Attach the unit in a secure location. Two 8-32 threaded inserts are providedin the area above the USER INTERFACE PANEL to install the UUT.A custom bracket may be created to mount to these inserts for testing theUUT in a desired location.2. Hook up the pneumatic lines - attaching the high port (HI) on the calibratorto the high port on the UUT and the low port (LO) on the calibratorto the low port on the UUT.3. Hook up electrical - (See Diagram 23, pg. 32)EXPERT SYSTEM - (See Page 33)8.0 CALIBRATING/TESTING A TRANSDUCER/TRANSMITTERMANUAL CALIBRATION:1. Select UUT tab. Select UUT ID from list and verify.2. Select REAL TIME tab3. Connect UUT according to UUT Connection Guide (Above).4. Press the -FS button (will be updated in the target pressure window) itwill generate the lowest pressure of the UUT range, wait until pressure isachieved.5. At this point, you may adjust the zero adjustment on the UUT until theoutput is within desired tolerance.6. Once zero is adjusted, press the +FS button (target pressure will againupdate in window) wait until pressure is achieved. You may adjust thespan potentiometer until within desired specification.7. Unit should be calibrated at this point. To verify, select TEST tab.AUTOMATED TEST:1. Select TEST tab2. Select UUT from list, (if not available, follow instructions for creatingnew).3. If selected test profile is not desired test, then select NEW test from list.4. Press DO TEST button and wait for completion.EXPERT SYSTEM TEST:(see page 33)31
Page 1: User ManualMicro-CalModel 869Very L
Page 4 and 5: 9.0 MICRO-CAL MANAGER INTERFACE9.1
Page 6 and 7: 2.0 INTRODUCTIONDOCUMENTING PROCESS
Page 8 and 9: 4.0 OPERATING FEATURES4.1 THE POCKE
Page 10 and 11: 5.3 USER INTERFACE PANELThe user in
Page 12 and 13: 6.0 POCKET PC INTERFACE SCREENSThe
Page 14 and 15: 6.3 TEST: GeneralScreen Instruction
Page 16 and 17: 6.33 TEST: Dither Control Page (Man
Page 18 and 19: 6.4 PROFILE: GeneralSetting up Test
Page 20 and 21: 6.5 UUT (UNIT UNDER TEST) SETUP: Ge
Page 22 and 23: UUT SUPPLEMENTAL PAGE1. Enter the U
Page 24 and 25: 6.51 UUT (UNIT UNDER TEST) SETUP: D
Page 26 and 27: 6.7 SYSTEMScreen Instructions (Diag
Page 28 and 29: EDIT DEFAULTS PAGEDisplay trend gra
Page 32 and 33: Standard 869Unit Under Test(Model 2
Page 34 and 35: 9.0 MICRO-CAL MANAGER INTERFACEThe
Page 36 and 37: Pocket PC Database - This list show
Page 38 and 39: New Button - This button opens a di
Page 40 and 41: Once a UUT ID is selected, the test
Page 42 and 43: 10.0 GLOSSARY OF TERMSAtmospheric P
Page 44 and 45: 12.0 SPECIFICATION DERIVATIONSTotal
Page 47 and 48: Non-LinearityRelationship of a cali
Page 49: 14.0 WARRANTY & LIMITATION OF LIABI

User Manual Micro-Calâ¢ Model 869 - Dipl.ing. Houm AS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

User Manual Micro-Calâ¢ Model 869 - Dipl.ing. Houm AS