Kingfisher PLUS+
Kingfisher G30 Manual - ioSelect
Kingfisher G30 Manual - ioSelect
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
G30 Processor Specifications<br />
Processor<br />
Word Size<br />
Flash Memory<br />
SDRAM<br />
NV Static RAM<br />
Realtime Clock<br />
Realtime Clock Backup<br />
Note: flash memory and NV<br />
static RAM does not require<br />
battery backup<br />
Communications Ports<br />
Ethernet Protocols<br />
Supported<br />
OLED Display<br />
Cirrus EP9301 (ARM9), 133 MHz maximum (internal)<br />
32 bit data bus (internal)<br />
16 MB. Permanent memory. Used to store the RTU configuration, logic,<br />
retained variables and event logs. If power to the G30 processor is lost,<br />
non-retained variables and the current state of execution will be reset.<br />
32 MB<br />
32 kB (128 kB optional). Permanent memory (NV = non volatile). Initial<br />
storage location of event logs. Event logs are then transferred to Flash.<br />
Yes. Accuracy + 1 minute/month (after calibration, at calibrating<br />
temperature)<br />
Super-capacitor<br />
TBD/50 hours @ 25/70 C up to 1000 hours operation<br />
TBD/TBD hours @ 25/70 C after 5 years<br />
TBD/TBD hours @ 25/70 C after 10 years<br />
Port 1: 10 or 100 Mbps Twisted Pair Ethernet. Has auto speed and link<br />
detect<br />
Port 2: USB 2.0 Host, Full Speed (12 Mbps max)<br />
Port 3: Option card<br />
TCP/IP, UDP, TCP, ARP and ICMP<br />
TCP/UDP <strong>Kingfisher</strong> protocol port number: 4058<br />
Color 96 x 64 pixel OLED (Organic Light Emitting Diode)<br />
Displays 8 lines of 19 characters<br />
LEDs (left to right) LED1: Power ON = Power OK<br />
LED2:<br />
Currently unassigned<br />
LED3:<br />
Currently unassigned<br />
LED4:<br />
Currently unassigned<br />
Push buttons<br />
Three - UP (left), DOWN (middle) and ENTER (right)<br />
Configuration Software Toolbox <strong>PLUS+</strong><br />
RTU Address Range 1-65535<br />
Supported Protocols<br />
<strong>Kingfisher</strong>, Modbus, DNP3, SNMP and more. For a complete list, please<br />
obtain Protocols.PDF from www.rtunet.com/support<br />
Logic Processing<br />
IEC 61131-3, Implemented using ISaGRAF Version 5.xx<br />
Input voltage range<br />
9 to 30 VDC<br />
Power Consumption<br />
2.5 W maximum<br />
Environment<br />
Operating Temperature -40 to 70 C<br />
EMC & Safety Compliance<br />
Port Isolation<br />
Dimensions -<br />
G30 Stand Alone RTU<br />
Operating Humidity<br />
5-95% RH @ 0 to 40 C non-condensing<br />
C-Tick<br />
Ethernet port: Working voltage in respect to system earth/ground must not<br />
exceed 150 VAC maximum. Isolation voltage (transient): 1 kV.<br />
USB Port: None<br />
Option Card Port: Depends on the Option Card installed.<br />
175 H x 70 W x 128 D mm (includes mounting brackets)<br />
G30 Hardware Manual 1.3 www.rtunet.com/support Page 6
Change language