SATRONIC - Control boxes for oil burners
SATRONIC - Control boxes for oil burners
SATRONIC - Control boxes for oil burners
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
certified Qualitysystem<br />
ISO 9001 / EN 29001<br />
Reg. Nr. 10529 A Honeywell Company TTO 872 / 876<br />
Oil burner safety control<br />
For <strong>burners</strong> on hot-air heaters, as well as<br />
<strong>burners</strong> above 30 kg/h in intermittent<br />
operation, 1- or 2-stage.<br />
Flame detectors:<br />
- Photoresistor MZ 770 S<br />
- Flicker detector IRD 911 / 1010<br />
INTRDUCTION<br />
The <strong>oil</strong> burner automatic safety control TTO 872, resp.,<br />
TTO 876 controls and monitors <strong>burners</strong> on hot air heaters,<br />
as well as <strong>burners</strong> with an <strong>oil</strong> consumption of over 30 kg/h<br />
(approved and certifcated acc. to DIN 4787).<br />
If the infrared flicker detector IRD 911 or 1010 is utilized as<br />
flame monitor, even red hot combustion chamber walls<br />
cannot affect the safe operation, since this sensor exclusively<br />
responds to the flame.<br />
The <strong>oil</strong> burner automatic safety control TTO 876 is fully<br />
interchangeable with the type TTO 836. The automatic<br />
control TTO 872 is – with the exception of the flame detector<br />
– compatible with type TTO 810. When replacing type<br />
TTO 810, the photo-cell FZ 711 has also got to be replaced<br />
by an MZ 770 S.<br />
The different heights are compensated <strong>for</strong> by mounting the<br />
pushbutton extension (art. No. 70601).<br />
Instead of the pushbutton extension, it is also possible to<br />
mount the remote reset device FR 870 (art. No. 70700, refer<br />
to the documentation "Remote Reset device FR 870").<br />
The <strong>oil</strong> burner control <strong>boxes</strong> TTO 872.2 / 876.2 are<br />
equipped with a low-voltage protection according to<br />
DIN-EN 230.<br />
TYPES AVAILABLE<br />
TTO 872.2 without connecting terminal <strong>for</strong> <strong>oil</strong> pre-heater<br />
TTO 876.2 with bridging contact and connection <strong>for</strong> <strong>oil</strong><br />
pre-heater.<br />
CONSTRUCTIONAL FEATURES<br />
The automatic control is housed in a non-inflammable,<br />
transparent, plug-in type plastic case and contains the<br />
thermo-mechanical and electronic combined time element,<br />
the flame monitor part and the reset device.<br />
On the top of the unit there are the illuminated pushbutton<br />
<strong>for</strong> indication of malfunctions and reset, as well as the screw<br />
<strong>for</strong> central mounting.<br />
The base can be equipped with additional loop terminals<br />
and - together with the various possibilities <strong>for</strong> cable entry<br />
- enables a universal wiring.<br />
1<br />
TECHNICAL DATA<br />
400e/05/94<br />
Operating voltage 220 / 240 V (-15... +10%)<br />
50 Hz (40 - 60 Hz)<br />
Rating fuse max. 10 A rapid, 6 A slow<br />
Power consumption approx. 5 VA<br />
Max. load per output 4 A ohmic (resistive)<br />
valve outputs 2 A ohmic (resistive)<br />
total 6 A ohmic (resistive)<br />
Pre-purge time 20 sec<br />
Pre-ignition time 20 sec<br />
Post-ignition time 2 - 4 sec<br />
Delay time valve 2 approx. 40 sec<br />
Ignition safety time<br />
Waiting period after shut-<br />
5 sec max.<br />
down due to malfunction<br />
Flame detector<br />
approx. 60 sec<br />
MZ 770 S <strong>for</strong> side-on and end-on viewing<br />
IRD 911 / 1010 <strong>for</strong> side-on and end-on viewing<br />
Light sensitivity MZ 770 S<br />
Detector current during<br />
better than 8 Lux<br />
operation<br />
Connection to<br />
flame detector<br />
min. 48 μA<br />
MZ 770 S 2 m cable length maximum<br />
IRD 911 / 1010 up to 100 m cable length<br />
Weight, incl. base 0.25 kg<br />
Mounting position Any<br />
Insulation Standard IP 44<br />
Recommended ambient<br />
operating temperatur <strong>for</strong><br />
control and flame detector -20° C... +60° C