TRANSDEV CATALOGUE 2018 MARCH.pdf

SEARCH
BACK TO MAIN CONTENTS
HARDWARE
Bushes
DRIVELOCK® 50 Bushes
DRIVELOCK® Bushes
Ød
ØD
Ød
ØD
data
Recommended shaft & hub tolerances
for full torque transmission are:
Other Belts
Stock no.
d
(mm)
TYPE DL50
L
Machining Not self-centering • Small radial dimensions • Low torques 2.4 to 1300Nm •
• Can be stacked in series (up to 4) to increase torque
D
(mm)
L
(mm)
T
F
(Nm)
< 40mm diameter
Shafts h6 Hub H7
> 40mm diameter
Shafts h8 Hub H8
Bores 6 to 70mm
P
(N/mm 2 )
DL50/ 6 6 9 4.5 2.4 0.84 75 3.8
DL50/ 7 7 10 4.5 3 0.86 70 3.9
DL50/ 8 8 11 4.5 4.7 1.17 90 5.3
DL50/ 9 9 12 4.5 7.9 1.76 105 15.6
DL50/ 10 10 13 4.5 9.5 1.91 105 15.6
DL50/ 12 12 15 4.5 11.4 1.91 90 15.6
DL50/ 13 13 16 4.5 13.1 2.02 90 15.6
DL50/ 14 14 18 6.3 22.3 3.18 90 25.4
DL50/ 15 15 19 6.3 24.3 3.24 85 25.4
DL50/ 16 16 20 6.3 27.3 3.42 85 25.4
DL50/ 17 17 21 6.3 29.8 3.51 85 25.4
DL50/ 18 18 22 6.3 32.4 3.61 80 25.4
DL50/ 19 19 24 6.3 49 5.22 110 36
DL50/ 20 20 25 6.3 53 5.33 105 36
DL50/ 22 22 26 6.3 66 6 115 36
DL50/ 24 24 28 6.3 73 6.13 110 36
DL50/ 25 25 30 6.3 72 5.77 95 36
DL50/ 28 28 32 6.3 86 6.33 100 36
DL50/ 30 30 35 6.3 91 6.08 85 36
DL50/ 32 32 36 6.3 131 8.24 115 45
DL50/ 35 35 40 7 171 9.77 110 54
DL50/ 36 36 42 7 169 9.39 100 54
DL50/ 38 38 44 7 181 9.55 95 54
DL50/ 40 40 45 8 231 11.57 105 66
DL50/ 42 42 48 8 235 11.22 95 66
DL50/ 45 45 52 10 353 15.71 95 99
DL50/ 48 48 55 10 572 23.44 135 132
DL50/ 50 50 57 10 602 24.08 130 132
DL50/ 55 55 62 10 670 24.35 125 132
DL50/ 56 56 64 12 790 28.2 115 157.2
DL50/ 60 60 68 12 860 28.6 110 157.2
DL50/ 70 70 79 14 1300 37.10 110 200
DL50 consists of a pair of conical rings and can be used in series (up to 4 sets) to give higher torque ratings.
Note: Customer to supply clamping ring or equipment.
L
T +44 (0)1202 675 555 F +44 (0)1202 677 466 E sales@transdev.co.uk transdev.co.uk 735
Fa
(kN)