Catalog_Sprinkler attachment_EN_2023

TECHNICAL INFORMATION
Characteristic values for injection anchor XV Plus
Loads for injection system VMU Plus with anchor rods VMU-A/IG/VM-A, galvanised, A4
and HCR for masonry in accordance with European Technical Assessment ETA-13/0909.
Characteristic values for solid blocks without perforated sleeve 1)
Anchor rods 1) : Steel ≥ FKL 5.8, A4, HCR ≥ FKL 70 M8 M10 M12 IG-M8
Building bricks Mz-DF acc. to EN 771-1, bulk density: 1.6 kg/dm 3 , minimum format: 240 x 115 x 55 mm (e.g. Unipor)
Anchoring depth hef mm 80 90 100 100
Axial spacing scr mm 240 270 300 300
Minimum axial spacing smin mm 120 120 120 120
Edge spacing ccr mm 120 135 150 150
Minimum edge spacing cmin mm 60 60 60 60
Minimum component thickness (masonry) hmin mm 110 120 130 130
Permissible tensile load
for compressive strength
Permissible transverse load
for compressive strength
fb ≥ 10 N/mm 2 perm. N kN 1.00 1.00 1.14 1.14
fb ≥ 20 N/mm 2 perm. N kN 1.29 1.57 1.71 1.71
fb ≥ 28 N/mm 2 perm. N kN 1.57 1.71 1.94 1.94
fb ≥ 10 N/mm 2 perm. V kN 1.00 1.00 1.00 1.00
fb ≥ 20 N/mm 2 perm. V kN 1.43 1.43 1.43 1.43
fb ≥ 28 N/mm 2 perm. V kN 1.57 1.57 1.57 1.57
Lime-sand brick KS-NF acc. to EN 771-2, bulk density: 2.0 kg/dm 3 , minimum format: 240 x 115 x 71 mm (e.g. Wemding)
Anchoring depth hef mm 80 90 100 100
Axial spacing scr mm 240 270 300 300
Minimum axial spacing smin mm 120 120 120 120
Edge spacing ccr mm 120 135 150 150
Minimum edge spacing cmin mm 60 60 60 60
Minimum component thickness (masonry) hmin mm 110 120 130 130
Permissible tensile load
for compressive strength
Permissible transverse load
for compressive strength
Type MKT injection system VMU Plus for solid blocks without perforated sleeve
fb ≥ 10 N/mm 2 perm. N kN 1.29 1.29 1.29 1.29
fb ≥ 20 N/mm 2 perm. N kN 1.71 1.71 1.71 1.71
fb ≥ 27 N/mm 2 perm. N kN 2.00 2.00 2.00 2.00
fb ≥ 10 N/mm 2 perm. V kN 0.71 0.86 0.71 0.71
fb ≥ 20 N/mm 2 perm. V kN 1.14 1.29 1.14 1.14
fb ≥ 27 N/mm 2 perm. V kN 1.29 1.57 1.29 1.29
Solid block of lightweight concrete LAC acc. to EN 771-3, bulk density: 0.6 kg/dm 3 , minimum format: 300 x 123 x 248 mm (e.g. Bisotherm)
Anchoring depth hef mm 80 90 100 100
Axial spacing scr mm 240 270 300 300
Minimum axial spacing smin mm 120 120 120 120
Edge spacing ccr mm 120 135 150 150
Minimum edge spacing cmin mm 60 60 60 60
Minimum component thickness (masonry) hmin mm 110 120 130 130
Permissible tensile load fb ≥ 6 N/mm 2 perm. N kN 0.86 0.86 1.00 1.00
for compressive strength
Permissible transverse load
for compressive strength
fb ≥ 6 N/mm 2 perm. V kN 0.86 0.86 0.86 0.86
1)
Anchoring with perforated sleeve is permitted; technical data, see European Technical Assessment ETA-13/0909.
Permissible loads without the effects of axial and edge spacing to component edges.
Vertical and horizontal joints are mortared. The safety coefficient in accordance with ETAG is included (γM and γF).
Temperature range +24 °C/+40 °C − use category dry/dry.
07/2023
© Müpro - progress and quality
8/19