Catalog_Sprinkler attachment_EN_2023
Sprinkler attachment
Sprinkler attachment
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
TECHNICAL INFORMATION<br />
Characteristic values for injection anchor XV Plus<br />
Type MKT injection system VMU Plus solid blocks without perforated sleeve<br />
Loads for injection system VMU Plus with anchor rods VMU-A/IG/VM-A, galvanised, A4<br />
and HCR for masonry in accordance with European Technical Assessment ETA-13/0909<br />
Characteristic values for solid blocks without perforated sleeve 1)<br />
Anchor rods 1) : Steel ≥ FKL 5.8, A4, HCR ≥ FKL 70 M8 M10 M12 IG-M8<br />
Aerated concrete AAC6 acc. to <strong>EN</strong> 771-4, bulk density: 0.6 kg/dm 3 , minimum format: 499 x 240 x 249 mm (e.g. Porit)<br />
Anchoring depth hef mm 80 90 100 100<br />
Axial spacing scr mm 240 270 300 300<br />
Minimum axial spacing smin mm 100 100 100 100<br />
Edge spacing ccr mm 120 135 150 150<br />
cmin,N mm 75 75 75 75<br />
Minimum edge spacing<br />
cmin,v,II 2) mm 75 75 75 75<br />
cmin,v,_I_ 3) mm 120 135 150 150<br />
Minimum component thickness (masonry) hmin mm 110 120 130 130<br />
Permissible tensile load fb ≥ 2 N/mm 2 perm. N kN 0.89 1.43 1.79 1.79<br />
for compressive strength<br />
Permissible transverse load<br />
for compressive strength<br />
fb ≥ 2 N/mm 2 perm. V kN 2.14 3.57 3.57 3.57<br />
1)<br />
Anchoring with perforated sleeve is permitted; technical data, see European Technical Assessment ETA-13/0909.<br />
2)<br />
Minimum edge spacing Cmin,v,ll for transverse load parallel to free edge.<br />
3)<br />
Minimum edge spacing Cmin,v,_l_ for transverse load vertical to free edge.<br />
Permissible loads without the effects of axial and edge spacing to component edges.<br />
Vertical and horizontal joints are mortared. The safety coefficient in accordance with ETAG is included (γM and γF).<br />
Temperature range +24 °C/+40 °C − use category dry/dry.<br />
Installation and plug characteristic values<br />
Characteristic values for solid blocks without perforated sleeve<br />
Anchor rods 1) : Steel ≥ FKL 5.8, A4, HCR ≥ FKL 70 M8 M10 M12 IG-M8<br />
Drilled hole diameter do mm 10 12 14 14<br />
Drilled hole depth ho mm 80 90 100 100<br />
Clearance hole in the add-on part df ≤ mm 9 12 14 9<br />
Brush diameter db ≥ mm 12 14 16 16<br />
Torque when anchoring Tinst,max Nm 2 (14 for building bricks Mz-DF)<br />
Amount of mortar per drill hole ml 4.1 6.6 10 10<br />
Drill holes per cartridge VMU Plus 280 piece 58 36 24 24<br />
Drill holes per cartridge VMU Plus 345 piece 74 46 30 30<br />
1)<br />
Anchoring with perforated sleeve is permitted; technical data, see European Technical Assessment ETA-13/0909.<br />
07/<strong>2023</strong><br />
8/20 © Müpro - progress and quality