ExtraClassSylalbus2009jan-AD7FO

Recommendations

Info

Rev 2.02 E6C08 In Figure E6-5, the schematic symbol for a NAND gate is number 2 If not A and B are 1 then the output is 1. Input A Input B output 0 0 0 0 1 1 1 0 1 1 1 1 E6C09 In Figure E6-5, the schematic symbol for an OR gate is number 3. If either A or B input are 1 then the output is 1. Input A Input B output 0 0 0 0 1 1 1 0 1 1 1 1 E6C10 In Figure E6-5, the schematic symbol for a NOR gate is number 4. If neither A or B are 1 then the output will be 1. Input A Input B output 0 0 1 0 1 0 1 0 0 1 1 0 E6C11 In Figure E6-5, the schematic symbol for the NOT operation (inverter) is number 5. If the input is high the output is low, if the input is low the output will be high. Input Output 0 1 1 0 E6D Optical devices and toroids: vidicon and cathode-ray tube devices; charge-coupled devices (CCDs); liquid crystal displays (LCDs); toroids: permeability, core material, selecting, winding E6D01 The electron beam is deflected in a vidicon by varying electromagnetic fields. Jack Tiley <strong>AD7FO</strong> Page 58 3/15/2009
Rev 2.02 E6D02 Cathode ray tube (CRT) persistence refers to the length of time the image remains on the phosphor screen after the beam is turned off. E6D03 If a cathode ray tube (CRT) is designed to operate with an anode voltage of 25,000 volts, and the anode voltage is increased to 35,000 volts the image size will decrease. E6D04 Exceeding the anode voltage design rating can cause a cathode ray tube (CRT) to generate X-rays. E6D05 A charge-coupled device (CCD) samples an analog signal and passes it in stages from the input to the output. E6D06 A charge-coupled device (CCD) in a modern video camera stores photo-generated charges as signals corresponding to pixels. E6D07 A liquid-crystal display (LCD) is a display that uses a crystalline liquid to change the way light is refracted. E6D08 Core permeability (for a given size core) is the property that determines the inductance of a toroidal inductor with a 10-turn winding. E6D09 The usable frequency range of inductors that use toroidal cores, assuming a correct selection of core material for the frequency being used is from less than 20 Hz to approximately 300 MHz. E6D10 One important reason for using powdered-iron toroids rather than ferrite toroids in an inductor is that powdered-iron toroids generally have better temperature stability. Applications for powdered Iron toroids would be oscillator and filter circuits where inductance stability with temperature is important. . E6D11 Ferrite beads are commonly used as VHF and UHF parasitic suppressors at the input and output terminals of transistorized HF amplifiers. E6D12 A primary advantage of using a toroidal core instead of a solenoidal core in an inductor is that toroidal cores contain most of the magnetic field within the core material. E6D13 Forty three turns of wire will be required to produce a 1-mH inductor using a ferrite toroidal core that has an inductance index (AL) value of 523 millihenrys/1000 turns. N turns = 1000 x (√ (L / AL)) or N turns = 1000 x (√ (1 / 523)) or 43.7 turns Jack Tiley <strong>AD7FO</strong> Page 59 3/15/2009
Page 1 and 2:
Rev 2.02 Preparing for the Extra cl
Page 3 and 4:
Rev 2.02 Guide to using this syllab
Page 5 and 6:
Rev 2.02 SUBELEMENT E4 -- AMATEUR R
Page 7 and 8: Rev 2.02 ELEMENT 4 - EXTRA CLASS QU
Page 9 and 10: Rev 2.02 E1A09 (Band Plan Chart) Th
Page 11 and 12: Rev 2.02 E1B13 (FCC Rules) Communic
Page 13 and 14: Rev 2.02 E1D08 (FCC Rules) The 2 me
Page 15 and 16: Rev 2.02 E1E20 (FCC Rules) You must
Page 17 and 18: Rev 2.02 SUBELEMENT E2 - OPERATING
Page 19 and 20: Rev 2.02 E2A13 Geosynchronous satel
Page 21 and 22: Rev 2.02 E2B17 Immunity from fading
Page 23 and 24: Rev 2.02 E2D02 The definition of
Page 25 and 26: Rev 2.02 SUBELEMENT E3 -- RADIO WAV
Page 27 and 28: Rev 2.02 E3C01 Auroral activity cau
Page 29 and 30: Rev 2.02 E4A06 A spectrum analyzer
Page 31 and 32: Rev 2.02 E4B09 High impedance input
Page 33 and 34: Rev 2.02 E4C06 If t he thermal nois
Page 35 and 36: Rev 2.02 E4D11 Third-order intermod
Page 37 and 38: Rev 2.02 SUBELEMENT E5 -- ELECTRICA
Page 39 and 40: Rev 2.02 E5B Time constants and pha
Page 41 and 42: Rev 2.02 Example 2: To find the ang
Page 43 and 44: Rev 2.02 j 50 -j 25 E5B12 The phase
Page 45 and 46: Rev 2.02 j 600 -j300 E5C04 In polar
Page 47 and 48: Rev 2.02 Parallel circuit solutions
Page 49 and 50: Rev 2.02 R=300 Ω XL= (2 π FL) or
Page 51 and 52: Rev 2.02 Power Factor represents th
Page 53 and 54: Rev 2.02 SUBELEMENT E6 -- CIRCUIT C
Page 55 and 56: Rev 2.02 Field-effect transistors e
Page 57: Rev 2.02 E6B12 Junction diodes are
Page 61 and 62: Rev 2.02 E6E04 The technique used t
Page 63 and 64: Rev 2.02 E6F07 Cadmium sulfide will
Page 65 and 66: Rev 2.02 E7A07 An AND gate produces
Page 67 and 68: Rev 2.02 When a Class C rather than
Page 69 and 70: Rev 2.02 E7C01 In a low-pass filter
Page 71 and 72: Rev 2.02 E7D02 One characteristic o
Page 73 and 74: Rev 2.02 E7E05 A pre-emphasis netwo
Page 75 and 76: Rev 2.02 E7F08 One purpose of a mar
Page 77 and 78: Rev 2.02 E7G17 The typical output i
Page 79 and 80: Rev 2.02 E7H19 A phase-locked loop
Page 81 and 82: Rev 2.02 E8A06 The approximate rati
Page 83 and 84: Rev 2.02 E8B13 In time division mul
Page 85 and 86: Rev 2.02 E8D07 An electromagnetic w
Page 87 and 88: Rev 2.02 E9A10 Antenna bandwidth is
Page 89 and 90: Rev 2.02 E9B10 The “Method of Mom
Page 91 and 92: Rev 2.02 E9C09 The elevation angle
Page 93 and 94: Rev 2.02 E9D09 An advantage of usin
Page 95 and 96: Rev 2.02 E9E08 An SWR greater than
Page 97 and 98: Rev 2.02 E9F11 A 1/8-wavelength tra
Page 99 and 100: Rev 2.02 E9H05 The main drawback of
Page 101 and 102: Rev 2.02 SUBELEMENT E0 -- SAFETY [1
Page 103 and 104: Rev 2.02 Jack Tiley AD7FO Page 103
Page 105 and 106: Rev 2.02 Capacitors in series C= __
Page 107 and 108: Rev 2.02 Impedance of complex serie
Page 109 and 110:
Rev 2.02 Calculating Component valu
Page 111 and 112:
Rev 2.02 AC Voltage Calculations Th
Page 113:
Rev 2.02 Jack Tiley AD7FO Page 113
show all

ExtraClassSylalbus2009jan-AD7FO

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?