Standardbeschreibung Produktschnittstelle Stahlbau - Dlubal Software

Standardbeschreibung Produktschnittstelle Stahlbau 4/2000 - Teil 2 105#134=VERTEX(28,7517.0,80.0,0.0,$);#135=MEMBER_LOCATION(’Hoe_1998-12-22T17:32:00_ML06’,6,’1998-12-22T17:32:00’,#123,#116,$,’Stirnplatte First’,#132,#133,#143,.M.,0.00,-20.0,$,$,$,$,$);/* Bauteilposition Gehrungssteife */#136=CROSS_SECTION(3,.B.,$,’BL20’,$,$,160.0,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$,$);#137=MEMBER(4,#136,#21,$,’P1202’,’Blech 450X160X20’,LAENGEN_TYP(450.0),$,$,$);#138=VERTEX(29,0.0,0.0,5000.0,$);#139=VERTEX(30,300.0,0.0,4795.0,$);#140=VERTEX(31,0.0,-80.0,5000.0,$);#141=MEMBER_LOCATION(’Hoe_1998-12-22T17:32:00_ML07’,7,’1998-12-22T17:32:00’,#137,#104,$,’Gehrungssteife’,#138,#139,#140,.M.,0.00,-25.0,$,$,$,$,$);/* Gehrungsschnitt Riegel im First*/#142=VERTEX(32,7517.0,0.0,0.0,$);#143=VERTEX(33,7500.0,0.0,300.0,$);#144=VERTEX(34,7517.0,-80.0,0.0,$);#145=VERTEX(35,-10.0,0.0,$,-100.0,$);#146=VERTEX(36,-10.0,0.0,$,100.0,$);#147=VERTEX(37,310.0,0.0,$,100.0,$);#148=VERTEX(38,310.0,0.0,$,-100.0,$);#149=POLYLINE(1,(#145,#146,#147,#148,#145));#150=CUTOUT(1,#149,#142,#143,#144,20.0,-1.0,.MITER_SQUARE.);/* Gehrungsschnitt Riegel in Ecke*/#152=VERTEX(39,0.0,0.0,0.0,$);#153=VERTEX(40,280.7,0.0,300.0,$);#154=VERTEX(41,0.0,80.0,0.0,$);#155=VERTEX(42,-10.0,0.0,$,-100.0,$);#156=VERTEX(43,-10.0,0.0,$,100.0,$);#157=VERTEX(44,500.0,0.0,$,100.0,$);#158=VERTEX(45,500.0,0.0,$,-100.0,$);#159=POLYLINE(2,(#155,#156,#157,#158,#155));#160=CUTOUT(2,#159,#152,#153,#154,10.0,-1.0,.MITER_SQUARE.);/* Gehrungsschnitt Stiel in Ecke*/#162=VERTEX(46,5000.0,0.0,0.0,$);#163=VERTEX(47,4719.3,0.0,300.0,$);#164=VERTEX(48,5000.0,80.0,0.0,$);#165=VERTEX(49,-10.0,0.0,$,-100.0,$);#166=VERTEX(50,-10.0,0.0,$,100.0,$);#167=VERTEX(51,500.0,0.0,$,100.0,$);#168=VERTEX(52,500.0,0.0,$,-100.0,$);#169=POLYLINE(3,(#165,#166,#167,#168,#165));#170=CUTOUT(3,#169,#162,#163,#164,10.0,-1.0,.MITER_SQUARE.);ENDSEC;END-ISO-10303-21;