25.02.2013 Views

1993_Motorola_Linear_Interface_ICs_Vol_2.pdf

1993_Motorola_Linear_Interface_ICs_Vol_2.pdf

1993_Motorola_Linear_Interface_ICs_Vol_2.pdf

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

MAXIMUM RATINGS<br />

MC2830<br />

Rating Symbol Value Unit<br />

Supply <strong>Vol</strong>tage VCC 10 V<br />

Operation Temperature Range TA o to +70 °c<br />

Storage Temperature Range Tstg -65 to + 150 °C<br />

Loading Current: Pin 3 10 200 /LA<br />

Pin 6 ISWO 2.0 mA<br />

ELECTRICAL CHARACTERISTICS (VCC = 50 V Input Frequency = 10kHz Loading Resistor = 50 kOhm, TA = 25°CI<br />

Characteristic Pin Symbol Min Typ Max Unit<br />

Supply <strong>Vol</strong>tage 8 VCC 1.8 - 8.0 V<br />

Quiescent Current 8 ID - - 2.0 mA<br />

MIC AMP Open Loop Gain AVOL - 80 - dB<br />

Total Harmonic Distortion of MIC AMP 3 THD - 1.0 - %<br />

(VO = 0.1 Vrmsl<br />

Maximum MIC AMP Output Swing 3 Vo - 0.16 - Vrms<br />

ALC Range (-6.0 dB, R1 = 33 k, Vin = 1.0 VI 3 ALC 40 50 - dB<br />

Ripple Rejection 3 RR - 55 - dB<br />

Voice Trigger Level Above Noise Vsln - 3.0 - dB<br />

Switch Output Current<br />

Switch Output <strong>Vol</strong>tage<br />

(lSWO = 2.0 mAl High<br />

Low<br />

Pin No. Function<br />

1 MICIN<br />

2 NF<br />

3 MIC OUT<br />

4 GND<br />

5 ALC<br />

6 SWO<br />

7 NSC<br />

8 VCC<br />

PIN FUNCTION DESCRIPTION<br />

6 ISWO - - 2.0 mA<br />

6 VSWO V<br />

4.6 - -<br />

- - 0.4<br />

Description<br />

Input of the microphone amplifier. The gain of the amplifier is set by the external components of<br />

the Rf, R2, and C2 (See formula 21.<br />

This is the negative feedback input pin of the microphone amplifier.<br />

Output of the microphone amplifier. It is designed to drive a maximum load current of 200 pA.<br />

The ground pin.<br />

This pin is for the ALC level detector filter. An RC is connected to this pin.<br />

This is the output pin of the voice activated switch. A resistor at this pin sets the voice trigger<br />

level above the noise level. The current drain of this pin is around 20 pA typical with a switch<br />

"off" state. The maximum output voltage level is VCC-VCES with a maximum output current of<br />

2.0 mA. As shown in Figure 3, this output is used to connect a switch time delay circuit to unify<br />

the "on" time. In Figure 3, C5 is the time delay capacitor which controls the "on" time of TR1.<br />

The Noise Storing Capacitor at this pin sets the rise time and decay time. The rise time is<br />

determined by the constant of the R5C4.<br />

This pin has a low voltage operation from 1.8 to 8.0 <strong>Vol</strong>ts.<br />

MOTOROLA LINEAR/INTERFACE <strong>ICs</strong> DEVICE DATA<br />

8-43

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!