Mixed-Signal IC Design Kit Training Manual - Electrical & Computer ...

More documents

Recommendations

Info

Calibre DRC Flow • Edit the Calibre DRC runset file (tsmc35DRC.cal): – Layout Path – Layout Primary – Include ‘Calibre-drc-cur’, the Calibre-drc-cur is linked to the DRC command file “CM35S5_4M.22b” • Run the batch mode of Calibre DRC: – calibre –drc –hier tsmc35DRC.cal 148 Mixed-Signal IC Design Kit
Calibre LVS Flow • Using “v2lvs” command of Calibre to translate the Verilog file from SE to the netlist for LVS. – Add the verilog module and subckt of analog block in tsmc35_lvs_ms.v and tsmc35_lvs_ms.spi, respectively. – v2lvs -v Verilog -l tsmc35_lvs_ms.v -o Output_netlist -s tsmc35_lvs_ms.spi -c cic -n • Edit the Calibre LVS runset file (tsmc35DRC.cal ): – Layout Path & Primary – Source Path & Primary – Include ‘Calibre-lvs-cur’, the Calibre-lvs-cur is linked to the DRC command file “cali035pMM5V_2P4M.lvs” 149 Mixed-Signal IC Design Kit
Page 2 and 3:
Day 1 Introduction of Mixed-Signal
Page 4 and 5:
SoC IP Based Design CORE Zone 4: Gl
Page 7 and 8:
Sensor Analog chip Sensor Integrati
Page 9 and 10:
Challenge of Integration • High d
Page 11 and 12:
Conventional Design Concept for Blo
Page 13:
Digital Model Abstraction Digital m
Page 16 and 17:
Enabling the Top-Down Design • Be
Page 18 and 19:
Top-Down Design Methodology Top-Dow
Page 20 and 21:
What Can’t Be Expected with Mixed
Page 22 and 23:
Digital Abstraction Mixed-Signal Si
Page 24 and 25:
Basics of Mixed Signal Simulation
Page 26 and 27:
Core Modification Glued Mixed-Signa
Page 29 and 30:
The Cadence environment can be invo
Page 31 and 32:
Verimix Mixed-Signal Tool Environme
Page 33 and 34:
Before the Design Creation • Syst
Page 35 and 36:
Device / Analog leaf cell The block
Page 37 and 38:
Partition Requirement • The desig
Page 39 and 40:
Interface Elements • Generated au
Page 41 and 42:
Analog Modeling for Mixed Signal De
Page 43 and 44:
Analog Hardware Description Languag
Page 45 and 46:
Disciplines Electrical magnetic the
Page 47 and 48:
Analog Modeling Issues • The Anal
Page 49 and 50:
MS HDL Simulation Flow 49 Mixed-Sig
Page 51 and 52:
Creating the HDL View of Designed B
Page 53 and 54:
Creating Analog Block and Symbol Cr
Page 55 and 56:
Integrating the whole design within
Page 57 and 58:
Schematics in Verilog-A Modules 57
Page 59 and 60:
Modelwrtier: the utility for creati
Page 61 and 62:
Digital Stimuli Analog Stimuli Addi
Page 63 and 64:
1. Create a behavioral view for the
Page 65 and 66:
Create Config View for Simulation T
Page 67:
After Setting Configuration The Hie
Page 70:
The default value can be preset in
Page 73 and 74:
Change View Selection With Hierarch
Page 76 and 77:
Specify Simulation Environment Use
Page 78 and 79:
Choosing Simulator/Directory/Host T
Page 80 and 81:
Level 1 Digital to Analog Interface
Page 82 and 83:
Level 3 Digital to Analog interface
Page 84 and 85:
Modification of IE Parameters • T
Page 87 and 88:
Some of the parameter values might
Page 89 and 90:
Define the signals to plotted after
Page 91 and 92:
module CCADCtop; supply1 N2; supply
Page 93 and 94:
Simulation Options for Digital Simu
Page 95 and 96:
Run Log Files Message for digital s
Page 97 and 98: • After Simulation, the selected
Page 99 and 100: Invoke by Tool Parametric Analysis
Page 101 and 102: Feature of HDL debug • Set breakp
Page 103 and 104: Analog blocks Digital domain Layout
Page 105 and 106: • Definition: Prepare Data for SE
Page 107 and 108: Cadence Abstract Generator • Cade
Page 109 and 110: Entering Technology Information •
Page 111 and 112: • After you specify technology in
Page 113 and 114: • Pins: - The Abstract Generator
Page 115 and 116: • Verify: Verify - During the ver
Page 117 and 118: • LEF file • Verilog file • C
Page 119 and 120: Verilog File of TSMC .35um 2P4M •
Page 122 and 123: • LEF file • Verilog file • C
Page 124 and 125: environment.gcf GCF File (gcf (head
Page 126 and 127: … Header( Library("IMatrix8x8") D
Page 128 and 129: CTLF File of TSMC .35um 2P4M • Di
Page 130 and 131: Place IO Constraints Create placeIO
Page 132 and 133: Import LEF File • Before creating
Page 134 and 135: Import Verilog File • CIC provide
Page 136 and 137: Place Analog Block • Select the b
Page 138 and 139: Add PRDIODE • To support a separa
Page 140 and 141: Placement • Place -> Cells • Qp
Page 142 and 143: Use Ultra Router • The ultra rout
Page 144 and 145: Prepare for Layout Verification •
Page 146 and 147: Modify Layout • As the layout of
Page 150 and 151: Calibre LVS Flow (Cont.) • Add an
Page 152 and 153: Mixed Signal Parasitic Simulation
Page 154 and 155: Transistor Level Post-Layout Simula
Page 156 and 157: Timemill Input Stimulus File • Cr
show all

Mixed-Signal IC Design Kit Training Manual - Electrical & Computer ...

Create successful ePaper yourself

Delete template?

Save as template?