TOOLED THICK COMPOSITES by ARVEN H. SAUNDERS III ...

More documents

Recommendations

Info

(Pal, 2005) Pal, R. “Porosity-dependence of Effective Mechanical Properties of Pore- solid Composite Materials”, Journal of Composite Materials, Vol. 39, No. 13, pp. 1147-1158, 2005. (Palanikumar, 2008) Palanikumar, K., Prakash, S., and Shanmugam, K., “Evaluation of Delamination in Drilling GFRP Composites”, Materials and Manufacturing Processes, 24: 858-864, 2005. (Petterssen 2009) Petterssen, F., Saxen, H., and Deb, K., “Genetic Algorithm-Based Multicriteria Optimization of Ironmaking in the Blast Furnace”, Materials and Manufacturing Processes, 24: 343-349, 2009. (Rai, 1997) Rai, N. and Pitchumani, R. "Optimal Cure Cycles for the Fabrication of Thermosetting-matrix Composites", Polymer Composites, 18(4), 566-581, 1997. (Rodriguez, 2004) Rodriguez, E., Giacomelli, F., Vàzquez, A., “Permeability–Porosity Relationship in RTM for Different Fiberglass and Natural Reinforcements”, Journal of Composite Materials, Vol. 38, No. 3, pp. 259-268, 2004. (Saunders, 1996) Saunders, A. , Buczek, M., Mason, D., and Lee, C.W., Adaptive Control Cure Monitoring (ACCM), Final Report, 1999, Aviation Applied Technology Directorate, U.S. Army. (Sheldon, 2001) Sheldon, K.E., Anderson-Cook, C.M., O'Brien, W.F., "Analysis Methods to Control Performance Variability and Costs in Aircraft Turbine Engine Manufacturing", American Society of Composites Conference, Blacksburg, Va., Sept 2001 (Shin, 2000) Shin, D.D. and Hahn, H.T., "A Consistent Cure Kinetic Model for AS4/3502 Graphite/epoxy", Composites: Part A, Vol. 31, p.991-999, 2000. 76
(Walia, 2006) Walia, R., Shan, H., and Kumar, P., “Parametric Optimization of Centrifugal Force-Assisted Abrasive Flow Machining (CFAAFM) <strong>by</strong> the Taguchi Method”, Materials and Manufacturing Processes, 21: 384-397, 2006. (Yang, 2006) Yang, Y., “Optimization of Injection-Molding Process of Short Glass Fiber and Polytetrafluoroethylene Reinforced Polycarbonate Composites via Design of Experiments Method: A Case Study”, Materials and Manufacturing Processes, 24: 915-921, 2006. 77
Page 1 and 2:
PROCESS MODELING SYSTEM FOR PRESS C
Page 3 and 4:
ACKNOWLEDGEMENTS This dissertation
Page 5 and 6:
TABLE OF CONTENTS ACKNOWLEDGEMENTS
Page 7 and 8:
4. RESULTS ........................
Page 9 and 10:
4.7 Acceptable IM7/3501-6 Flexbeam
Page 11 and 12:
CHAPTER 1 INTRODUCTION 1.1 Backgrou
Page 13 and 14:
Inspection and evaluation technique
Page 15 and 16:
Figure 1.3. Fiber/Layer Waviness in
Page 17 and 18:
CHAPTER 2 REVIEW OF RELATED RESEARC
Page 19 and 20:
greatly lag in temperature. As a re
Page 21 and 22:
Physics-based models are often used
Page 23 and 24:
equation above can be solved by wri
Page 25 and 26:
keep the cure on track. Examples of
Page 27 and 28:
(Chen, 2002). However, because they
Page 29 and 30:
during cure and consolidation. In a
Page 31 and 32:
initially in the cure process but w
Page 33 and 34:
Figure 3.1. Generic Flexbeam with T
Page 35 and 36: Permeability describes the resistan
Page 37 and 38: patterns velocity and timing during
Page 39 and 40: S ii 2 f r = 4k ii ( 1− V where r
Page 41 and 42: proportion of the applied pressure
Page 43 and 44: At any timestep in the simulation,
Page 45 and 46: constant displacement ramp followed
Page 47 and 48: 6 5 4 3 2 1 0 Figure 3.8. Model Con
Page 49 and 50: decrease for CVs that were previous
Page 51 and 52: total resin volume rate for the lam
Page 53 and 54: series electrical circuits—a left
Page 55 and 56: hold these values, with R(k) being
Page 57 and 58: • Resin pressure causes resin flo
Page 59 and 60: where α is cure, An is the pre-exp
Page 61 and 62: temperature conditions. The princip
Page 63 and 64: cycle. The ability to optimize temp
Page 65 and 66: Temperature (C) 200 180 160 140 120
Page 67 and 68: Temperature (C) 200 180 160 140 120
Page 69 and 70: useful; as pointed out by Cirisciol
Page 71 and 72: Flexbeam (z) Height and Tool Lid Po
Page 73 and 74: 55 minutes into the S2/8552 cycle,
Page 75 and 76: Resin Pressure (Pa) 1.2E+06 1.0E+06
Page 77 and 78: -7.138E-12 -7.138E-12 -6.517E-12 -5
Page 79 and 80: keeping the level below a certain t
Page 81 and 82: feedback to set the temperature cur
Page 83 and 84: (Chen, 2002) Chen, Y., "Modeling of
Page 85: (Mitra, 2009) Mitra, K., Majumder,
show all

TOOLED THICK COMPOSITES by ARVEN H. SAUNDERS III ...

Create successful ePaper yourself

Delete template?

Save as template?