OPERATING INSTRUCTIONS NORDAC Frequency Inverters

More documents

Recommendations

Info

General example of a load diagram: 25
8.0 Disruptions and faults Urgent error messages: - displayed immediately e.g. Actual fault motor temp. inv. 1 Old error messages: - Up to 5 preceding fault messages are stored and cannot be deleted e.g. - Displayed in option 24 ("Old fault") Fault history Motor temp. inv. 1 - Call up with Value keys - 1 to 5, order in which the errors occurred - Type of fault with identification digit 1 to 20 Displayed text Message Possible cause No fault 0 No fault has occurred Overtemp. inv. 1 Thermostatic switch Ventilator failure, overload in inverter has tripped Coolant temperature too high or defective components length of line (compare point 10.3) Overtemp. 2 Temperature sensor PTC thermistor or thermal cutout motor in motor has tripped has high resistance or is open or instrument leads affected by interference potentials If no temperature sensors are connected --> bridge Terminals 9 and 10 Overvoltage 3 DC link voltage monitor Braking too fast has tripped Operating without brake chopper GND shortage Mains voltage too high Defective braking chopper Overcurrent 4 Excess current longer than 30 sec. Overload Output short circuit Wrong motor/inverter selection Acceleration or braking time too short Boost/magnetic saturation too high Important: motor operation different from generator operation! --> it may be necessary to use a different parameter set Parameter loss 5 Internal computer check signals Switch-off while computer was storing data an error The EEPROM or EPROM ist defective The EPROM version has been changed --> switch on the inverter again or recharge it Zerop. curr. 1 6 Internal monitoring Defective components Phase 1 Zerop. curr. 2 7 Internal monitoring Defective components Phase 2 Zerop. curr. 3 8 Internal monitoring Defective components Phase 3 + 15 V error 9 + 15 V controller voltage error Power supply unit defective - 15 V error 10 - 15 V controller voltage error Power supply unit defective EEPROM error 11 Internal monitoring of the EEPROM Defective component No NMER 12 Internal monitoring Defective component NMER multiple 13 Internal monitoring Defective component UZER multiple 14 Internal monitoring Defective component Watchdog 15 Internal monitoring Program run error --> switch inverter on again GND shortage 16 Earth fault at the output terminals Motor or motor supply line defective EPROM error 17 Internal monitoring Defective components Charging err. 18 Monitoring of the charging facility Defective component Defective brake-chopper Interrupt err. 19 Internal monitoring Defective component Watchdog err. 20 Internal monitoring Defective component Note regarding "defective components": If the inverter can be acknowledged or switched on again, the fault is due to high interference potentials rather than to a component defect. 26
Page 1 and 2: GETRIEBEBAU NORD OPERATING INSTRUCT
Page 3 and 4: 1.0 General NORDAC frequency Invert
Page 5 and 6: 3.0 Frequency inverter dimensions V
Page 7 and 8: 4.2 Control section Connection for
Page 9 and 10: Terminal Function / Notes Data Sugg
Page 15 and 16: 5.1 Settings and displays possible
Page 17 and 18: 5.2 Description of settings and dis
Page 19 and 20: Menu displayed text descritption op
Page 21 and 22: Menu displayed text Description opt
Page 23 and 24: 6.0 Commissioning Before switching
Page 25: 7.0 Braking chopper Used for genera
Page 29 and 30: Note: If the maximum value is great
Page 31 and 32: 10.2 Effect on other consumers Main
Page 33: MODULAR SYSTEM TRANSMISSION TYPE AT

OPERATING INSTRUCTIONS NORDAC Frequency Inverters

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?