Euroview 70 Technical Manual - West Coast Vinyl Windows

Recommendations

Info

4.8 Mounting Parts for Window Installation of VEKA Coupling System in the Insulating Layer Pre-Installation of the mounting brackets on the side of the window (in window fabrication or at the building site) Structure: porous brick, sand-lime brick, concrete, porous concrete sash connector Sash Connector with: – installation screw nut AM8 -T for PVC windows Measurements and Marking AK distance HV height adjustment a axis-center distance min. 25 mm (valid for SFS fasteners) a r edge distance min. 30 mm (valid for SFS fasteners) AW support angle from 80 mm distance ALW turn round angle porous brick HVP height adjustment plate SM screw nut adjustable from outside* * in case you can’t drill the frame. Mounting Bracket JB-D pre-installed, with installation screw nut for PVC windows order code AK HV article no. JB- D50 - 30 - AM8 -T * 50 30 707 051 JB- D50 - 40 - AM8 -T * 50 40 707 052 JB- D50 - 60 - AM8 -T * 50 60 707 053 JB- D100 - 30 - AM8 -T 100 30 707 054 JB- D100 - 40 - AM8 -T 100 40 707 055 JB- D100 - 60 - AM8 -T 100 60 707 056 JB- D150 - 30 - AM8 -T 150 30 707 057 JB- D150 - 40 - AM8 -T 150 40 707 058 JB- D150 - 60 - AM8 -T 150 60 707 059 JB- D50 - 30 - SM- AM8 -T 50 30 707 025 JB- D50 - 40 - SM- AM8 -T 50 40 707 028 JB- D50 - 60 - SM- AM8 -T 50 60 707 029 JB- D100 - 30 - SM- AM8 -T 100 30 707 033 JB- D100 - 40 - SM- AM8 -T 100 40 707 036 JB- D100 - 60 - SM- AM8 -T 100 60 707 037 JB- D150 - 30 - SM- AM8 -T 150 30 707 038 JB- D150 - 40 - SM- AM8 -T 150 40 707 039 JB- D150 - 60 - SM- AM8 -T 150 60 707 040 Copyright by VEKA AG Technical specifications are subject to change. 03-07 4
Mounting Parts for Window Installation of VEKA Coupling System in the Insulating Layer Mounting Instruction for System JB-D Pre-Installation of the brackets at the building site (in advance and without window) 1. Place bracket JB-DK in the opening and push it to the bushing; required minimum edge distance ar is defined 2. Drill first hole into the building structure 3.Set brackt with supporting tools (hand gage) to the required distance (AK) 4. Drill second hole into the building structure (minimum axis-center distance a is guaranteed) 5. Install both fastener and tighten them 6. Check the distance 7. Adjust height adjustment plate (HVP) Pre-Installation of the jamb mounting brackets JB-D at the window The jamb mounting brackets JB-D can be installed during window fabrication or later at the building site. 1. Drill a tapped hole or drill through with a required diameter of 10.5 mm for AM8-T 2. Install the frame connector (AM8-T) 3.Turn the mounting brackets in and, if necessary, lock them for transport Window Installation on pre-installed brackets JB-DK 1. Deliver window to the building site 2. Place window on the already installed and adjusted brackets JB-DK 3. Adjust window at each side and center it 4. Screw window sill connector and bracket JB-DK together from the bottom Jamb fastening of the window at the wall with JB-D 1.Turn the mounting brackets JB-D sideways following the alignment of the wall (brick) 2. Drill first hole with a minimum edge distance (ar = 30mm) 3.Turn the first screw in the first hole, don’t pull it tight 4. Place window in the level vertically 5. Drill the second hole with a minimum axis-center distance of a = 25mm 6. Also turn the second screw and pull both screws tight 7. Check level Copyright by VEKA AG Technical specifications are subject to change. 03-07 4.9 1 2 3 4 5 6 7
Page 1 and 2:
VEKA INC EUROVIEW 70 TECHNICAL MANU
Page 3:
SECTION 1: PROFILE CHARTS
Page 14 and 15:
VEKA Commercial Window & Door Divis
Page 16 and 17:
SECTION 3: Size Limitations, Typica
Page 47:
SECTION 4: Profile Combinations & D
Page 145 and 146: SECTION 6: Coupling Systems
Page 147 and 148: EUROVIEW 70 STRUCTURAL LOAD CHARTS
Page 153: EUROVIEW 70 STRUCTURAL LOAD CHARTS
Page 180: Mounting Parts for Window Installat
Page 206 and 207: GÜTEGEMEINSCHAFT KUNSTSTOFF-FENSTE
Page 208 and 209: 1. Preface There are only few regul
Page 210 and 211: 4. Final measurements and determina
Page 212 and 213: 2. Scope All information given in t
Page 214 and 215: Check List for the Invitation to Te
Page 216 and 217: 3.1 Information Information about t
Page 218 and 219: Waste containing harmful substances
Page 220 and 221: 3.6 Roller shutter 3.6.1 Type ➔ 3
Page 222 and 223: 3.8 Sound insulation DIN 4109 appli
Page 224 and 225: 3.13 Structural fi fitting tting Th
Page 226 and 227: Fig. 2: Diagramfor the determinatio
Page 228 and 229:
4.4 Nominal carcass dimensions In c
Page 230 and 231:
4.6 Factors to be taken into consid
Page 232 and 233:
External window sill: (type, colour
Page 234 and 235:
This basic rules of the German Buil
Page 236 and 237:
6.1.1 General information about the
Page 238 and 239:
150 ca. 150 mm Please take into acc
Page 240 and 241:
Examples of fasteners in use are sh
Page 242 and 243:
6.2 Special connections 6.2.1 Addit
Page 244 and 245:
In case of greater element widths,
Page 246 and 247:
6.2.4 Couplings For the safe transf
Page 248 and 249:
6.3.1 Joint insulation E.g. the fol
Page 250 and 251:
In case of adhesive surfaces that a
Page 252 and 253:
taken from the IVD-Technical leafle
Page 254 and 255:
6.3.5 Sealing materials Examples fo
Page 256 and 257:
6.10 Recycling of dismantled window
Page 258 and 259:
Oxygen in the air can also cause co
Page 260 and 261:
Chart 7: Dew point temperature agai
Page 262 and 263:
- 2°C 1°C 4°C 7°C 10°C 12,6°C
Page 264 and 265:
These changes have to be taken up b
Page 266 and 267:
Construction basics Material Densit
Page 268 and 269:
8. Legal requirements The construct
Page 270 and 271:
DIN EN ISO 717-1 Acoustics - Rating
Page 272 and 273:
DIN EN 12211* Windows and doors - R
Page 274 and 275:
DIN 18516-1 Cladding for external w
Page 276 and 277:
WITHIN THE QKE · WWW.GKFP.DE
show all

Euroview 70 Technical Manual - West Coast Vinyl Windows

Create successful ePaper yourself

Delete template?

Save as template?