Euroview 70 Technical Manual - West Coast Vinyl Windows

Recommendations

Info

Examples of fasteners in use are shown in fig. 13 and fig. 14. Consider the corresponding information of the manufacturer! Tubular frame dowel BTI – window dowel Tapping screw Instantaneous axis Claw/tie bolt EJOT – Lateral force anchor distance from edge Fixing bracket SFS JB-D SFS JB-D distance from edge SFS JB SFS JB Angle WITHIN THE QKE · WWW.GKFP.DE The installation Fig. 13: Fasteners for temporary element fastening Chapter 6 33
Chapter 6 34 The installation Fastening in old buildings For the fastening of the main frame in the bottom part, choose fasteners which do not inevitably open the armouring chamber from the recess depth. If this is not possible, seal the armouring chamber resist- antly. RAL-GÜTEGEMEINSCHAFT KUNSTSTOFF-FENSTERSYSTEME seal Claw/tie bolt Angle Tubular frame dowel Caution: Ensure that load do not cause damage Consider the dimensioning of the load transferring building components Fixing bracket seal seal Tubular frame dowel Tapping screw Fig. 14: Fasteners for the lower element fastening The choice of the fasteners is made according to the type of masonry. Angle In case of vertically perforated brick masonry, the masonry has to be filled in the area of the dowels (e.g. utilisation of injection mortar Fischer FIS VS 150 C). According to fig. 14 different connections are possible. Caution: Ensure that load do not cause damage
Page 1 and 2:
VEKA INC EUROVIEW 70 TECHNICAL MANU
Page 3:
SECTION 1: PROFILE CHARTS
Page 14 and 15:
VEKA Commercial Window & Door Divis
Page 16 and 17:
SECTION 3: Size Limitations, Typica
Page 47:
SECTION 4: Profile Combinations & D
Page 145 and 146:
SECTION 6: Coupling Systems
Page 147 and 148:
EUROVIEW 70 STRUCTURAL LOAD CHARTS
Page 149 and 150:
Page 151 and 152:
Page 153:
Page 178 and 179:
4.8 Mounting Parts for Window Insta
Page 180:
Mounting Parts for Window Installat
Page 206 and 207: GÜTEGEMEINSCHAFT KUNSTSTOFF-FENSTE
Page 208 and 209: 1. Preface There are only few regul
Page 210 and 211: 4. Final measurements and determina
Page 212 and 213: 2. Scope All information given in t
Page 214 and 215: Check List for the Invitation to Te
Page 216 and 217: 3.1 Information Information about t
Page 218 and 219: Waste containing harmful substances
Page 220 and 221: 3.6 Roller shutter 3.6.1 Type ➔ 3
Page 222 and 223: 3.8 Sound insulation DIN 4109 appli
Page 224 and 225: 3.13 Structural fi fitting tting Th
Page 226 and 227: Fig. 2: Diagramfor the determinatio
Page 228 and 229: 4.4 Nominal carcass dimensions In c
Page 230 and 231: 4.6 Factors to be taken into consid
Page 232 and 233: External window sill: (type, colour
Page 234 and 235: This basic rules of the German Buil
Page 236 and 237: 6.1.1 General information about the
Page 238 and 239: 150 ca. 150 mm Please take into acc
Page 242 and 243: 6.2 Special connections 6.2.1 Addit
Page 244 and 245: In case of greater element widths,
Page 246 and 247: 6.2.4 Couplings For the safe transf
Page 248 and 249: 6.3.1 Joint insulation E.g. the fol
Page 250 and 251: In case of adhesive surfaces that a
Page 252 and 253: taken from the IVD-Technical leafle
Page 254 and 255: 6.3.5 Sealing materials Examples fo
Page 256 and 257: 6.10 Recycling of dismantled window
Page 258 and 259: Oxygen in the air can also cause co
Page 260 and 261: Chart 7: Dew point temperature agai
Page 262 and 263: - 2°C 1°C 4°C 7°C 10°C 12,6°C
Page 264 and 265: These changes have to be taken up b
Page 266 and 267: Construction basics Material Densit
Page 268 and 269: 8. Legal requirements The construct
Page 270 and 271: DIN EN ISO 717-1 Acoustics - Rating
Page 272 and 273: DIN EN 12211* Windows and doors - R
Page 274 and 275: DIN 18516-1 Cladding for external w
Page 276 and 277: WITHIN THE QKE · WWW.GKFP.DE
show all

Euroview 70 Technical Manual - West Coast Vinyl Windows

Create successful ePaper yourself

Delete template?

Save as template?