[10] TEST COMMAND, TROUBLE CODES - OlsonBros
[10] TEST COMMAND, TROUBLE CODES - OlsonBros
[10] TEST COMMAND, TROUBLE CODES - OlsonBros
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Main Sub<br />
code code<br />
24 09 Printer counter clear<br />
(PRT.CLR.)<br />
<strong>10</strong> FAX counter clear (FAX<br />
CLR.) (Executable only<br />
when the FAX is installed.)<br />
13 Scanner counter clear<br />
(SCAN CLR.)<br />
14 SPF JAM total counter clear<br />
(S JAM TTL CLR.) (Disabled<br />
when set to OC)<br />
15 Scanner mode counter clear<br />
(S-MODE CLR.)<br />
25 01 Main motor operation check<br />
(MAIN MOTOR CHK)<br />
<strong>10</strong> Polygon motor operation<br />
check (LSU CHK)<br />
Contents Details of function/operation<br />
[Function]<br />
When [ENTER/START] key is pressed, the printer counter value is cleared to 0, and "000,000" is displayed<br />
on the LCD.<br />
[Operation]<br />
1) Initial display<br />
24-09 PRT.CLR.<br />
CLEARED 000,000<br />
[Function]<br />
When PRINT switch is pressed, the FAX count value is set to 0 and "000,000" is displayed on the<br />
LCD.<br />
[Operation]<br />
1) Initial display<br />
24-<strong>10</strong> FAX CLR.<br />
CLEARED 000,000<br />
[Function]<br />
When [ENTER/START] key is pressed, the scanner counter value is cleared to 0, and "000,000" is<br />
displayed on the LCD.<br />
[Operation]<br />
1) Initial display<br />
24-13 SCAN CLR.<br />
CLEARED 000,000<br />
[Function]<br />
When [ENTER/START] key is pressed, the SPF JAM total counter value is cleared to 0, and<br />
"000,000" is displayed on the LCD.<br />
[Operation]<br />
1) Initial display<br />
24-14 S JAM TTL CLR.<br />
CLEARED 000,000<br />
[Function]<br />
When [ENTER/START] key is pressed, the scanner mode counter value is cleared to 0, and<br />
"000,000" is displayed on the LCD.<br />
[Operation]<br />
1) Initial display<br />
24-15 S-MODE CLR.<br />
CLEARED 000,000<br />
[Function]<br />
When [ENTER/START] key is pressed, the main motor (and the duplex motor in the case of a duplex<br />
model) is operated for 30sec.<br />
To reduce toner consumption, if the developing unit is installed, the developing bias, the main<br />
charger, and the grid are also outputted.<br />
In this case, laser discharge is required when stopping the motor, the polygon motor is also operated<br />
at the same time. Check for installation of the developing unit. If it is not installed, the high voltage<br />
above is not outputted and only the motor is rotated.<br />
To check the developing bias, install the developing unit.<br />
After completion of 30sec operation, the machine goes into the sub code entry standby mode.<br />
[Operation]<br />
1) Initial display<br />
25-01 MAIN MOTOR CHK<br />
EXECUTING...<br />
[Function]<br />
When [ENTER/START] key is pressed, the Bios is called to rotate the polygon motor for 30sec.<br />
After completion of 30sec operation, the operation is turned off with the Bios and the machine goes<br />
into the sub code entry standby mode.<br />
[Operation]<br />
1) Initial display<br />
25-<strong>10</strong> LSU CHK<br />
EXECUTING...<br />
AR-168S/168D <strong>TEST</strong> <strong>COMMAND</strong>, <strong>TROUBLE</strong> <strong>CODES</strong> <strong>10</strong> - 12