[10] TEST COMMAND, TROUBLE CODES - OlsonBros

More documents

Recommendations

Info

Main Sub code code 46 15 FAX mode density adjustment (Super fine) (Executable only when the FAX is installed.) Contents Details of function/operation 18 Image contrast adjustment (300dpi) (GAMMA 300) [Function] When [START] key is pressed, scan is started with the entered exposure adjustment value and the data of the selected mode on the FAX side is changed to the entered value. For the density adjustment value table data, refer to TC46-13 (FAX mode density adjustment (normal text).) [Operation] 1) Initial display ADJUST EXP. S-FINE XX ("XX" is the corresponding exposure adjustment value of the super fine mode stored on the FAX side.) 2) Enter a 2-digit value as the exposure adjustment value with [10KEY]. ADJUST EXP. S-FINE YY ("YY" is the entered exposure adjustment value.) [Function] Contrast is set for each mode. When this test command is executed, the current se value is displayed in 2 digits (Default: 50). Change the set value and press [START] key to make a copy under the set value. When the set value is increased, the contrast becomes higher. When the set value is decreased, the contrast becomes lower. In this case, only Exp.3 copy is made. When, however, the setting is made to make higher contrast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast, Exp1. and Exp.5 copies become lower contrast, too. Press [←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD. (Adjustment value: 1 – 99) ∗ No density display on LCD. [Operation] The operation is similar to test command 46-01. AR-168S/168D TEST COMMAND, TROUBLE CODES 10 - 20 3) Scan start (self print) ADJUST EXP. S-FINE SCAN YY 4) Print start (self print) ADJUST EXP. S-FINE PRINT YY After completion of printing, returns to “2)” display. Mode Display item Default LED AE mode (300dpi) AE 50 COPY mode lamp TEXT mode (300dpi) TEXT 50 PRINT mode lamp PHOTO mode PHOTO 50 SCAN mode lamp TS mode (TEXT) (300dpi) TSTXT 50 PRINT mode lamp SCAN mode lamp TS mode (AE) (300dpi) TSAE 50 COPY mode lamp SCAN mode lamp
Main Sub code code 46 19 Exposure mode setting (AE MODE) Contents Details of function/operation 20 SPF exposure correction (EXP.LEVEL SPF) (Disabled when set to OC) [Function] When this test command is executed, the code number of the current set gamma table is displayed. (Default: Japan -1/Ex Japan -2) Enter the code number corresponding to the desired gamma table, and press [←/→] key to change the mode and write into the EEPROM. When setting the γ table, press [→] key to change to the AE operation mode, and the current set code number of the AE operation mode is displayed. (Default: 0) Enter the code number corresponding to the desired AE operation mode and press [←/→] key to change the mode and write into the EEPROM. When [→] key is pressed in AE operation mode setting, the mode is changed to the PHOTO image process setting and the code number of the current set PHOTO image process setting is displayed. (Default: 0) Enter the code number corresponding to the desired PHOTO image process setting and press [←/→] key to change the mode and write into the EEPROM. Mode Display item Code number Setting content Remark γ GAMMA 1 2 Image quality priority mode Toner consumption priority mode Japan default EX Japan default AE AE 0 1 Lead edge stop Real time process Default PHOTO PHOTO 1 2 Error diffusion process Dither process Default [Operation] 1) Initial display 46-19 AE MODE GAMMA 2( 1-2) 2) [→] Mode selection 2) [←] Mode selection [Function] Used to adjust the exposure correction amount in the SPF mode. The adjustment is made by adjusting Vref voltage variation for the OC mode. When this test command is executed, the current set value is displayed in 2 digits (Default: 50). Change the set value and press [START] key to save the setting and make a copy. When the set value is increased, copy becomes darker. When the set value is decreased, copy becomes lighter. (Adjustment range: 1 – 99) [Operation] The operation is similar to test command 46-01. 46-19 AE MODE AE 0( 0-1) 46-19 AE MODE PHOTO 1( 1-2) Mode Display item Default Remark SPF SPF 50 AR-168S/168D TEST COMMAND, TROUBLE CODES 10 - 21 3) [10KEY] Value input 46-19 AE MODE AE 1( 0-1) 4) [ENTER/START] Save the set value. The machine goes to the sub code entry standby mode.
Page 1 and 2: [10] TEST COMMAND, TROUBLE CODES 1.
Page 3 and 4: 4. Descriptions of various test com
Page 5 and 6: Main Sub code code 5 01 Operation p
Page 7 and 8: Main Sub code code 8 01 Developing
Page 9 and 10: Main Sub code code 22 02 Maintenanc
Page 11 and 12: Main Sub code code 22 21 Scanner co
Page 13 and 14: Main code Sub code Contents Details
Page 15 and 16: Main Sub code code 26 43 Side void
Page 17 and 18: Main Sub code code 43 05 Fusing tem
Page 19: Main Sub code code 46 12 Density ad
Page 23 and 24: Main Sub code code 46 32 Copier col
Page 25 and 26: Main Sub code code 49 01 Download m
Page 27 and 28: Main Sub code code 50 06 Copy lead
Page 29 and 30: Main Sub code code 51 02 Resist amo
Page 31 and 32: Main Sub code code 64 01 Self print
Page 33 and 34: Main Sub code code 66 05 Signal sen
Page 35 and 36: Main Sub code code 66 13 Dial test
Page 37 and 38: Main Sub code code 66 32 Receive da
Page 39 and 40: 5. Trouble codes A. Trouble codes l
Page 41: Main Sub code code Details of troub

[10] TEST COMMAND, TROUBLE CODES - OlsonBros

Create successful ePaper yourself

Delete template?

Save as template?