REFERENCE MANUAL E8-V5 - SIC-Venim s.r.o.

More documents

Recommendations

Info

Subsequently, in the parameter edit mode, you will need to enter the diameter of the part present in the chuck (this parameter will be requested on the general marking parameters entry screen), so that marking can be performed accordingly. If the D axis option is present in the system, but you want to carry out plane marking, enter the value ‘zero’ for the diameter of the workpiece. For normal use of the D axis, it must be mounted to the left of the marking head and the axis of the part must be aligned exactly with the X movement head. RATIO : Transmission ratio V MIN, V MAX, V ORG : : Axis rate of movement ACCEL. : Acceleration ratio OFFSET Y : Maximum time of actuator movement SENSOR : Type of sensor: Normal, Complemented or no sensor at origin. RETURN TO ORIGIN : (YES or NO) generates return to origin at in cycle. Accessory Feeder V MIN V ORG D axis RATIO V MIN V MAX V ORG ACCEL. OFFSET Y SENSOR PRIORITE RETURN TO ORIGIN Feeder Marking position Evac. position RATIO MASKED TIME RETURN Part detection sensor Clamping on output V MAX ACCEL. Marking position : Feeder feed position for marking Evac. position : If this position differs from the marking position, the loader will move to this position at the end of marking. RATIO : Transmission ratio V MIN, V MAX, V ORG : : Axis rate of movement ACCEL. : Acceleration ratio MASKED TIME RETURN : Loader return to origin position during marking cycle (Incompatible if the evacuation position is not the same as the marking position) Part detection sensor : Detects workpiece input number (if present) Clamping on output : Output number managing plate clamping (if present) NOTREFE8V5US – R01 24/51
4 - I/O parameters ( ) : Access from MARKING MODE by and Inputs 1 and 2 cannot be parametered (reserved to cycle start and stop). Warning : in case of unconsistancy of choices, some values may change automatically. Input settings NONE File sel. Pause Air pressure Outputs settings None Cycle Last Error Pause ready No Part Part Wear Input not used Input is used for file selection, combined with other inputs Input used to validate pause (If not parametered, start button is the signal) Connected to pressure regulator for scribing (when available) Output not used Output is activated when cycle is in process Output is activated when last dot is marked, before returning to origin Activates itself when an error is detected Signal when in pause 5 - Priority of the axes for the first move ( ): from MARKING MODE by and This command is to generate movements in a specific order at the beginning and end of the cycle. Active when ready to start marking I/O SETTING Num Input Output STOP START Cycle Last File Sel. Error File Sel. Pause File Sel. Ready File Sel. NoPart File Sel. Part File Sel. Wear Auto-Sensing error: part not found within tolerances Auto-Sensing error: part found out of tolerances Stylus wear: signal linked to maintenance menu after X cycles. PRIORITY 1st 2nd 3rd Sortie 1 = X AXIS 2 = Y AXIS 3 = Z AXIS For first movement before marking (approach), the axis will run one after the other in the order appearing on the screen: 1st, 2nd, 3 rd . For origin return, order is on the opposite: 3rd, 2nd, 1st. NOTREFE8V5US – R01 25/51
Page 1: SIC MARKING 13 route de Limonest ZA
Page 4 and 5: 3 - DATA-MATRIX FORMAT.............
Page 6 and 7: - Entry fields In the active field
Page 8 and 9: 1 - FILE menu FILE VAR. MARKING CON
Page 10 and 11: DEFAULT SETTINGS REG Change to conf
Page 12 and 13: 3 - MARKING Menu FILE VAR. MARQUAGE
Page 14 and 15: 4 - CONFIGURATION Menu FILE VAR. MA
Page 16 and 17: PASSWORD SUP: Adjustment of passwor
Page 18 and 19: SCALE 1:1 : The graphic view is to
Page 20 and 21: STATE OF I/O: Caution, the ready ou
Page 22 and 23: 3 - Accessory parameters ( ): The c
Page 26 and 27: 6 - Parameters of marking cycle ( +
Page 28 and 29: 4 - EDIT Menu FIle EDIT MARK. FORMA
Page 30 and 31: 5 - MARKING Menu FICH EDIT MARQ. FO
Page 32 and 33: RS232: Send a stream to the HOST or
Page 34 and 35: VI - APPENDIXES 1 - QUALITY OF MARK
Page 36 and 37: ) Orientation = Vertical •Straigh
Page 38 and 39: 3 - Data-matrix format Square forma
Page 40 and 41: 7 - Description of serial ports a)
Page 42 and 43: c) « MARKER » connector This is a
Page 44 and 45: Cycle start Cycle underway End of m
Page 46 and 47: ) Use of the inputs/outputs with cl
Page 48 and 49: ARIAL FONT The ARIAL font is a spac
Page 50 and 51: OCR FONT NOTREFE8V5US - R01 50/51

REFERENCE MANUAL E8-V5 - SIC-Venim s.r.o.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?