Korg Microkorg Owner's Manual - zZounds.com
Korg Microkorg Owner's Manual - zZounds.com
Korg Microkorg Owner's Manual - zZounds.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Turning the power on<br />
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○<br />
○<br />
1. The power supply<br />
Before you connect the power supply, make sure that the power switch is turned off<br />
(i.e., in the outward position).<br />
Connecting the AC adaptor<br />
Firmly insert the plug of the included AC adaptor into the jack. Then connect the<br />
AC adaptor to an AC outlet.<br />
Never use any AC adaptor other than the included one.<br />
Inserting/exchanging batteries<br />
The microKORG can also be operated on batteries.<br />
Batteries are not included. You will need to purchase them<br />
separately.<br />
1 Make sure that the power switch on the microKORG is turned off.<br />
Then open the battery cover located on the bottom of the case.<br />
2 Insert six AA alkaline batteries.<br />
Be careful to observe the correct polarity of the batteries.<br />
3 Close the battery cover.<br />
Low battery display “ ”<br />
When the batteries run low, the display will indicate " ," and the "." at the far<br />
right will begin blinking. If you continue using the microKORG, the Protect setting<br />
will be turned on automatically, and you will be unable to edit program or global<br />
settings. We re<strong>com</strong>mend that you install new batteries or switch to the AC adaptor<br />
as soon as possible. If this state occurs while you are editing, and you want to save<br />
your settings, connect the AC adaptor and execute the Write operation.<br />
You can cancel the " " display by pressing the SHIFT key.<br />
Batteries that have be<strong>com</strong>e unusable should be removed from the microKORG<br />
as soon as possible. Leaving such batteries installed may cause malfunctions<br />
(due to battery leakage, etc.). You should also remove the batteries if you will<br />
not be using the microKORG for an extended period of time.<br />
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○<br />
○<br />
2. Turning the power on<br />
Before you turn on the microKORG’s power, you should lower the level of your<br />
monitor system or other connected output device.<br />
1 Turn the microKORG's VOLUME knob all the way toward the left.<br />
2 Press the power switch to turn on the power.<br />
The display will indicate the program number.<br />
3 Turn the microKORG's VOLUME knob toward the right to an appropriate<br />
position.<br />
4 Adjust the volume of your external output device.<br />
1, 3<br />
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○<br />
○<br />
3. Turning the power off<br />
After saving any necessary data (such as a program you have edited) turn the<br />
power off using the reverse order of the power-on procedure.<br />
Never turn the power off while data is being saved (i.e., while Write is executing).<br />
Doing so may damage the internal data.<br />
2<br />
6