Linear Way L

More documents

Recommendations

Info

Example 3 Separate mounting of slide units from track rails Linear Way Reference mounting surface Linear Way Table Bed Reference mounting surface Fig. 32 Example 3 When the slide units assembled on the track rail cannot be securely fixed to the table due to table construction, prepare one reference mounting surface on the bed and two reference mounting surfaces on the table, then proceed as follows. (See Fig. 32.) 1 Cleaning of mounting surfaces Remove burrs and blemishes from reference mounting surfaces and mounting surfaces of the machine using an oil-stone, etc., and then wipe the surfaces with clean cloth. (See Fig. 33.) Remove rust preventive oil and dirt from Linear Way reference mounting surfaces and mounting surfaces with clean cloth. Fig. 33 Cleaning of mounting surfaces 2 Temporary fixing of Linear Wayand track rails Correctly fit the reference mounting surface of Linear Waytrack rail onto the mating reference mounting surface of the bed, and temporarily fix the track rail with mounting bolts. (See Fig. 34.) During installation, ensure that the track rail mounting bolts do not interfere with the mounting holes. Temporarily fix Linear Waytrack rail onto the bed. Fig. 34 Temporary fixing of track rail 1N=0.102kgf=0.2248lbs. 1mm=0.03937inch 125
3 Final fixing of Linear Waytrack rail Firmly push the reference mounting surface of Linear Way track rail to the mating reference mounting surface of the bed using a small vise or clamp. Tighten the track rail mounting bolt at the position of the vise or clamp. Fix the track rail by progressively moving the vise or clamp from one rail end to the other. (See Fig. 35.) At this stage, leave Linear Waytrack rail temporarily fixed. Fig. 35 Fixing of track rail 4 Separation of slide units from track rails After noting the respective markings which identify correct assembly positions of slide units on Linear Wayand track rails, separate slide units from track rails. 5 Fixing of Linear Wayandslide units Correctly fit the reference mounting surfaces of Linear Wayandslide units to the mating reference mounting surfaces of the table and fix the slide units as shown in the figure. (See Fig. 36.) Fig. 36 Fixing of slide unit 6 Installing slide units on track rails Gently and gradually install the slide units which are fixed on the table onto the track rails which are fixed or temporarily tightened on the bed. Take care to maintain parallelism of the table to the track rails as the table is slid onto the rails. 7 Fixing of Linear Way track rail Fix the track rail of Linear Waywhile checking the smooth motion by moving the table. At this time, tighten the mounting bolt right behind the fixed slide unit of Linear Wayjust passed. Fix the track rail by repeating this procedure from one rail end to the other. 126
Page 2 and 3:
Description of Linear Way and Linea
Page 4 and 5:
3 Wide range of selections for high
Page 6 and 7:
Four-point contact structure 3 High
Page 8 and 9:
Parallel arrangement 3 Excellent lo
Page 10 and 11:
Interchangeable Specification Linea
Page 12 and 13:
Features of interchangeable specifi
Page 14 and 15:
Long-Term Maintenance Free Linear M
Page 16 and 17:
Stainless Series Linear Way and Lin
Page 18 and 19:
Linear Way and Linear Roller Way fo
Page 20 and 21:
Linear Way and Linear Roller Way fo
Page 22 and 23:
Lubrication Corrosion prevention Ca
Page 24 and 25: For Ordering When ordering assemble
Page 26 and 27: Accuracy Five classes of accuracy,
Page 28 and 29: Table 2.2 Accuracy of Linear Way L
Page 30 and 31: Table 2.4 Accuracy of Linear Way Mo
Page 32 and 33: Special Specifications Linear Way a
Page 34 and 35: Specified rail mounting hole positi
Page 36 and 37: With female threads for bellows (fo
Page 38 and 39: Rail cover platePS U.S. PATENT NO.
Page 40 and 41: With scrapers (for single slide uni
Page 42 and 43: Table 7 Parts for lubrication C-Sle
Page 44 and 45: R3 Grease nipple and supply nozzle
Page 46 and 47: Table 11 Applicable supply nozzles
Page 48 and 49: Table 13.1 Pipe joint for PT1/8 (St
Page 50 and 51: Table 15.1 Dimensions of bellows an
Page 52 and 53: Precautions for Use Mounting struct
Page 54 and 55: Mounting of Linear Way L The genera
Page 56 and 57: Corner radius and shoulder height o
Page 58 and 59: Table 17.2 Shoulder heights and cor
Page 60 and 61: Table 19 Shoulder heights and corne
Page 62 and 63: Table 21 Shoulder heights and corne
Page 64 and 65: Table 24.1 Shoulder height of the m
Page 66 and 67: Precautions for Mounting When mount
Page 68 and 69: Tightening torque of mounting bolts
Page 70 and 71: 2 Temporary fixing of Linear Way a
Page 72 and 73: Example 2 Operation requiring accur
Page 76 and 77: Example 4 Assembly of Linear Way Mo
Page 78 and 79: Mounting methods of datum track rai
Page 80 and 81: Mounting method for butt-jointing t
Page 82 and 83: Long-Term Maintenance Free Series U
Page 84 and 85: 1 Series ML 2 Size of rolling guide
Page 86 and 87: Table 3 Track rail with stopper pin
Page 88 and 89: C-Sleeve Linear Way L C-Sleeve Line
Page 90 and 91: Linear Way L series Shape Length of
Page 92 and 93: 1 Series Standard type Wide rail ty
Page 94 and 95: 8 Preload amount Clearance T0 Stand
Page 96 and 97: Table 6 Changed sizes of mounting h
Page 98 and 99: Table 8 Track rail with stopper pin
Page 100 and 101: Table 10.2 Standard and maximum len
Page 102 and 103: Mounting bolt Mounting bolts for th
Page 104 and 105: Linear Way L : Standard type Ball r
Page 106 and 107: Linear Way L : Wide rail type Ball
Page 108 and 109: Linear Way L : Wide rail type Ball
Page 110 and 111: Linear Way E series Shape Length of
Page 112 and 113: 1 Series Flange type mounted from t
Page 114 and 115: 7 Preload amount Clearance : TC Sta
Page 116 and 117: Table 5.1 Female threads for bellow
Page 118 and 119: Table 6 Changed size of mounting ho
Page 120 and 121: Track rail length Standard and maxi
Page 122 and 123: Recommended track rail mounting bol
Page 124 and 125:
Linear Way E : Flange type Flange t
Page 126 and 127:
Linear Way E : Flange type Flange t
Page 128 and 129:
Linear Way E : Block type Block typ
Page 130 and 131:
Low Decibel Linear Way E series Sha
Page 132 and 133:
1 Series Flange type mounted from t
Page 134 and 135:
Table 4 Combination of special spec
Page 136 and 137:
Table 5.2 Female threads for bellow
Page 138 and 139:
Table 8 Slide unit with double end
Page 140 and 141:
Recommended track rail mounting bol
Page 142 and 143:
Low Decibel Linear Way E: Flange ty
Page 144 and 145:
High Rigidity Type Linear Way U.S.
Page 146 and 147:
Identification number and specifica
Page 148 and 149:
Table 1.1 Models and sizes of Linea
Page 150 and 151:
8Preload amount Clearance T0 Standa
Page 152 and 153:
Table 4 Special specifications Spec
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Table 9 Slide unit with double end
Page 160 and 161:
Track rail length Standard and maxi
Page 162 and 163:
Table 11.3 Standard and maximum len
Page 164 and 165:
Linear Way H : Flange type Flange t
Page 166 and 167:
Linear Way H : Flange type Flange t
Page 168 and 169:
Linear Way H : Block type Block typ
Page 170 and 171:
Linear Way H : Compact block type C
Page 172 and 173:
Wide Rail Type Linear Way U.S. PATE
Page 174 and 175:
Page 176 and 177:
6 Preload amount Standard Light pre
Page 178 and 179:
Table 4.1 Special specifications of
Page 180 and 181:
D 1 1 1 1 B Fig. 1 Chamfers on refe
Page 182 and 183:
Table 7 Slide unit with capillary p
Page 184 and 185:
Track rail length Standard and maxi
Page 186 and 187:
Linear Way F : Flange type Flange t
Page 188 and 189:
Linear Way F : Block type Block typ
Page 190 and 191:
Linear Way U series Shape Model Min
Page 192 and 193:
1 Series Miniature typeLWUL Standar
Page 194 and 195:
Table 5 Slide unit with upper seals
Page 196 and 197:
Recommended track rail mounting bol
Page 198 and 199:
Linear Way U Ball non-retained type
Page 200 and 201:
Linear Roller Way Super X series Sh
Page 202 and 203:
1 Series Flange type mounted from t
Page 204 and 205:
8Accuracy class High Precision Supe
Page 206 and 207:
Table 5 Combination of special spec
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Table 9.1 Slide unit with double en
Page 214 and 215:
Table 10.2 Slide unit with scrapers
Page 216 and 217:
Table 11.2 Standard and maximum len
Page 218 and 219:
50 50 Deflection 40 30 20 10 T2 Upw
Page 220 and 221:
Linear Roller Way Super X : Flange
Page 222 and 223:
Linear Roller Way Super X : Block t
Page 224 and 225:
Linear Roller Way X LRWXBLRWXH U.S.
Page 226 and 227:
Page 228 and 229:
Table 2 Special specifications Butt
Page 230 and 231:
Table 6 Slide unit with scrapers (S
Page 232 and 233:
Linear Roller Way X : Block type Bl
Page 234 and 235:
Linear Way Module LWLMLWMLRWM U.S.
Page 236 and 237:
Page 238 and 239:
Table 1 Special specifications Spec
Page 240 and 241:
Linear Way Module Linear Way LM LWL
Page 242 and 243:
Linear Way Module Linear Roller Way
Page 244 and 245:
Track rail length Table 1 Standard
show all

Linear Way L

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?