Parameter setting - Knick

More documents

Recommendations

Info

Index U Ultrapure water 45 V Variable limits 50 Viewing level 41 W Warranty 2 Wiring example 21 Z Zero point correction 39 82 Protos 3400(X)
Icon Explanation of icons important for this module The Protos is in measuring mode. The Protos is in calibration mode. Function check is active. The Protos is in maintenance mode. Function check is active. The Protos is in parameter setting mode. Function check is active. The Protos is in diagnostics mode. NAMUR signals Function check. The NAMUR “function check” contact is active (factory setting: BASE module, contact K2, N/O contact). Current outputs as configured: • Currently measured value: The currently measured value appears at the current output • Last measured value: The last measured value is held at the current output • Fixed 22 mA: The output current is at 22 mA Failure: The NAMUR “failure” contact is active (factory setting: BASE module, contact K4, N/C contact). To view error message, call up: Diagnostics menu/Message list Maintenance: The NAMUR “maintenance request” contact is active (factory setting: BASE module, contact K2, N/O contact). To view error message, call up: Diagnostics menu/Message list Limit indication: Lower / upper range exceeded man Temperature detection by manual input Calibration - Step 1 of product calibration has been executed. The Protos is waiting for the sample value TC Calibration: Temperature compensation for process medium is active (Linear/Ultrapure water/Chart) In the plaintext display in front of a menu line: Access to next menu level with enter In the plaintext display in front of a menu line when it has been blocked by the Administrator against access from the Operator level. Designates the module slot (1, 2 or 3), allowing the clear assignment of measuredvalue/parameter displays in the case of identical module types. Indicates the active parameter set (The Protos provides two parameter sets A and B. Up to 5 sets can be added using additional functions and SmartMedia card.)
Page 1 and 2:
Measuring Module Protos ® CONDI 34
Page 4 and 5:
Contents Warranty .................
Page 6:
Contents Diagnostics functions . .
Page 9 and 10:
Safety information Caution! Never t
Page 11 and 12:
Modular concept and instruction man
Page 13 and 14:
Short description: Menu structure B
Page 15 and 16:
Short description: BASE module Prot
Page 17 and 18:
Terminal plate CONDI 3400(X)-051 Te
Page 19 and 20:
SE 655 / SE 656 sensor Dimension dr
Page 21 and 22:
Wiring example SE 655 / SE 656 sens
Page 23 and 24:
Passcode entry Enter passcode: Sele
Page 25 and 26:
Menu Display Configure measurement
Page 27 and 28:
Menu Display Select favorites 0.245
Page 29 and 30:
Calibration / adjustment Temperatur
Page 31 and 32: Menu Display Select calibration met
Page 33 and 34: Menu Display Automatic calibration
Page 35 and 36: Menu Display Manual entry of cal so
Page 37 and 38: Menu Display Product calibration Mo
Page 39 and 40: Calibration / adjustment Zero corre
Page 41 and 42: Parameter setting: Operating levels
Page 43 and 44: Parameter setting Call up parameter
Page 45 and 46: Parameter setting TC process medium
Page 47 and 48: Nitric acid HNO 3 c[% by wt] Hydroc
Page 49 and 50: Concentration chart (add. function)
Page 51 and 52: Setting the message parameters Mess
Page 53 and 54: Current outputs, contacts, OK input
Page 55 and 56: • Function characteristic Nonline
Page 57 and 58: NAMUR signals: Current outputs Beha
Page 59 and 60: Relay contacts: Protective wiring P
Page 61 and 62: Limit value, hysteresis, contact ty
Page 63 and 64: Switching parameter sets via OK2 Pa
Page 65 and 66: Activating Calculation Blocks Selec
Page 67 and 68: Setting diagnostics messages as fav
Page 69 and 70: Diagnostics Module diagnostics, sen
Page 71 and 72: Specifications l ------------------
Page 73 and 74: Annex: Minimum measuring spans for
Page 75 and 76: Parameter setting menu Display sett
Page 77 and 78: Calibration menu CONDI 3400(X)-051
Page 79 and 80: Index E EC Declaration of Conformit
Page 81: Index Parameter tables (Excel) 16 P
show all

Parameter setting - Knick

Create successful ePaper yourself

Delete template?

Save as template?