Omron SX inverter manual

More documents

Recommendations

Info

Category C2: Power Drive System (PDS) of rated voltage
1.5 Dismantling and scrapping The enclosures of the drives are made from recyclable material as aluminium, iron and plastic. Each drive contains a number of components demanding special treatment, for example electrolytic capacitors. The circuit boards contain small amounts of tin and lead. Any local or national regulations in force for the disposal and recycling of these materials must be complied with. 1.5.1 Disposal of old electrical and electronic equipment This information is applicable in the European Union and other European countries with separate collection systems. 1.6.2 Definitions In this manual the following definitions for current, torque and frequency are used: Table 3 Definitions Name Description Quantity I IN Nominal input current of VSD A RMS I NOM Nominal output current of VSD A RMS I MOT Nominal motor current A RMS P NOM Nominal power of VSD kW P MOT Motor power kW T NOM Nominal torque of motor Nm T MOT Motor torque Nm f OUT Output frequency of VSD Hz f MOT Nominal frequency of motor Hz n MOT Nominal speed of motor rpm I CL Maximum output current A RMS This symbol on the product or on its packaging indicates that this product shall be treated according to the WEEE Directive. It must be taken to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potentially negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling this product, please contact the local distributor of the product. Speed Actual motor speed rpm Torque Actual motor torque Nm Sync speed Synchronous speed of the motor rpm 1.6 Glossary 1.6.1 Abbreviations and symbols In this manual the following abbreviations are used: Table 2 Abbreviations Abbreviation/ symbol DSP VSD CP EInt UInt Int Long Description Digital signals processor Variable speed drive Control panel, the programming and presentation unit on the VSD Communication format Communication format Communication format Communication format The function cannot be changed in run mode 10 Introduction Omron SX inverter manual
Page 1 and 2: Cat. No. I127-EN-00B SX-V High powe
Page 4 and 5: Safety Instructions Precautions sev
Page 6 and 7: Precautions to be taken with a conn
Page 8 and 9: Contents 1. Introduction ..........
Page 10 and 11: 1. Introduction Omron SX-V is used
Page 14 and 15: 2. Mounting This chapter describes
Page 16 and 17: 2.2.2 Mounting schemes Membrane cab
Page 18 and 19: 2330 2330 1000 600 1200 600 Fig. 11
Page 20 and 21: 3. Installation The description of
Page 22 and 23: RFI-Filter Mains VSD maintenance sw
Page 24 and 25: 3.5.2 Tightening torque for mains a
Page 26 and 27: 4. Getting Started This chapter is
Page 28 and 29: 6. Set motor power [223]. 7. Set mo
Page 30 and 31: 5. Control Connections 5.1 Control
Page 32 and 33: 5.4 Connection example Fig. 24 give
Page 34 and 35: angle. Do not let the signal cable
Page 36 and 37: 6. Applications This chapter contai
Page 38 and 39: 7. Main Features This chapter conta
Page 40 and 41: One motor must stop before changing
Page 42 and 43: Stop RunL RunR Enable Reset +24 V X
Page 44 and 45: Torque [%] [4161] MaxAlarmMar (15%)
Page 46 and 47: 7.6.2 Fixed MASTER This is the defa
Page 48 and 49: 7.6.6 PID control When using the Pu
Page 50 and 51: 7.6.8 Checklist And Tips 1. Main Fu
Page 52 and 53: Stopping an additional pump This fi
Page 54 and 55: 46 EMC and Machine Directive Omron
Page 56 and 57: alarm messages. 300 Process Appl St
Page 58 and 59: The VSD will be started and stopped
Page 60 and 61: 100 0rpm Stp A 0.0A Menu 100 appear
Page 62 and 63:
Motor M2 44041-44048 172/180 to 174
Page 64 and 65:
Programming example: typedef struct
Page 66 and 67:
58 Serial communication Omron SX in
Page 68 and 69:
11.1.2 2nd Line [120] Sets the cont
Page 70 and 71:
Local/Remote key function [217] The
Page 72 and 73:
11.2.4 Motor Data [220] In this men
Page 74 and 75:
When the motor has no cooling fan,
Page 76 and 77:
PWM Mode [22E2] Default: Standard S
Page 78 and 79:
Menu [234] PTC contains functions t
Page 80 and 81:
The active set can be viewed with f
Page 82 and 83:
Number of Trips [251] Any number se
Page 84 and 85:
Communication information Modbus In
Page 86 and 87:
Min Alarm [25K] Delay time starts c
Page 88 and 89:
Modbus format UInt Brake Fault [25V
Page 90 and 91:
Communication Fault Time [2642]] De
Page 92 and 93:
Default: Speed F(AnIn) 0 Function o
Page 94 and 95:
Fieldbus format Long, 1=0.001 Modbu
Page 96 and 97:
pm 333 Acc MotPot Stp 16.0s A Nom.
Page 98 and 99:
Deceleration Ramp Type [338] Sets t
Page 100 and 101:
Default: Range: Depend on: 0 rpm -
Page 102 and 103:
Fieldbus format Modbus format PID r
Page 104 and 105:
Profibus slot/index 169/32 Fieldbus
Page 106 and 107:
n [367] Preset Ref 6, with default
Page 108 and 109:
PID sleep functionality This functi
Page 110 and 111:
11.3.9 Pump/Fan Control [390] The P
Page 112 and 113:
Change Timer [395] When the time se
Page 114 and 115:
Lower Band Limit [39C] If the speed
Page 116 and 117:
Run Times 1-6 [39H] to [39M] Unit:
Page 118 and 119:
Max Alarm [416] Max Alarm Margin [4
Page 120 and 121:
The default set levels for the (pre
Page 122 and 123:
Overvolt control [424] Used to swit
Page 124 and 125:
User Bipol mA 3 0-10V 4 2-10V 5 Use
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Profibus slot/index 169/145 Fieldbu
Page 132 and 133:
AnOut1 Advanced [533] With the func
Page 134 and 135:
Page 136 and 137:
Digital Out 2 [542] Relay 2 [552] N
Page 138 and 139:
Virtual Connection 1 Source [562] W
Page 140 and 141:
Communication information No. 1 2 3
Page 142 and 143:
Page 144 and 145:
Y Operator 2 [624] Selects the seco
Page 146 and 147:
Timer 1 Mode [642] Default: Off 0 D
Page 148 and 149:
Timer 2 T2 [655] Default: 0:00:00,
Page 150 and 151:
DC Link Voltage [719] Displays the
Page 152 and 153:
The example in Fig. 94 indicates th
Page 154 and 155:
Energy [733] Displays the total ene
Page 156 and 157:
Page 158 and 159:
150 Functional Description Omron SX
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
12.2 Trip conditions, causes and re
Page 168 and 169:
Table 28 Trip condition, their poss
Page 170 and 171:
Check external wiring, connections
Page 172 and 173:
Table 30 Brake resistor SX-V 400V t
Page 174 and 175:
When the "Safe Stop" condition is a
Page 176 and 177:
168 Options Omron SX inverter manua
Page 178 and 179:
Table 35 Typical motor power at mai
Page 180 and 181:
14.3 Operation at higher temperatur
Page 182 and 183:
14.6 Environmental conditions Table
Page 184 and 185:
176 Technical Data Omron SX inverte
Page 186 and 187:
Table 46 Type cables cross-sections
Page 188 and 189:
180 Technical Data Omron SX inverte
Page 190 and 191:
DEFAULT CUSTOM DEFAULT CUSTOM 2651
Page 192 and 193:
DEFAULT CUSTOM DEFAULT CUSTOM 5197
Page 194 and 195:
DEFAULT CUSTOM DEFAULT CUSTOM 81I I
Page 196 and 197:
89E DEFAULT DigOut status 89F AnIn
Page 198 and 199:
External Control Panel ............
Page 200 and 201:
(413) .............................
Page 202:
T Terminal connections ............
show all

Omron SX inverter manual

Create successful ePaper yourself

Delete template?

Save as template?