SX25 Series Process Controller - Spirax Sarco

More documents

Recommendations

Info

Second group parameters The display will show Stop tvn£ This is used to start the automatic tuning. Using this table enter the following values into these parameters. Press the enter key to save the value entered and to move to the next parameter. When the last parameter has been entered, press the enter key to save this value. To exit press the scroll key . The display will show: PASS pass Press the scroll key again and the display will return to the normal operating mode. The controller is ready to operate. Now enter the required set point of 20.0 bar by using the and keys. Parameter Description Default Customer Value set Values tune Tuning PID Stop Stop AdPt Adaptive tuning PID Stop Stop SL. u Set point ramp up Off Off SL. d Set point ramp down Off Off S.P. L Set point low limit 0.0 0.0 S.P. H Set point high limit 50.0 25.0 A2hy Alarm 2 hysteresis 0.5 0.5 A2L.b Alarm 2 latching and blocking none Ltch A3hy Alarm 3 hysteresis 0.5 0.5 A3L.b Alarm 3 latching and blocking none none t.F iL Time constant input filter Off Off In.Sh Input shift Off Off d.Err Error dead band Off Off St.OP Soft start output value Off Off Sa.OP Control output high limit 0.0 0.0 To improve control of the application, adjust the proportional band and integral time accordingly. 42 IM-P323-25 CH Issue 3
6.2 Example of temperature control for <strong>SX25</strong>-VMD The <strong>SX25</strong>-VMD controller is 'ILMN'. I L M N monitoring system temperature 8 0 0 2 with a RTD Pt100, and provides a Valve Motor Drive control signal to Enter the last digit for code 'O' the electric control valve. The configuration code is now entered,and the display will show: Configuration Code and parameters: • Temperature sensor with an effective range from 0°C to 100°C. • Control Valve with 20mm stroke and Valve Motor Drive electric actuator, speed 0.5mm/s . • Two Event alarms are required. Event Y2 set for active low process alarm set at 35°C with the blocking function. Event Y3 set for an active high deviation alarm set at 10°C. • The process temperature required is 60°C is the control temperature. Configuration code Using the and keys, enter the first part of the configuration code Press the enter key to save the value entered and to move to the next parameter. Use the enter key to review the data you have entered or press the scroll key to exit the configuration menu. o C vn¡t then press the enter key then press the enter key This selects Celsius or Fahrenheit for the temperature units. Using the table below enter the following values into the parameters. Parameter Description Default Value New Value Unit temperature units °C °C Code Change Security code 33 33 When the configuration menu is exited, the display will now show the normal operating mode, with the process variable at the top and the set point at the bottom. For example: With the controller configured, the parameters can now be entered. IM-P323-25 CH Issue 3 43 O 4
Page 1 and 2: 3231450/3 IM-P323-25 CH Issue 3 SX2
Page 3 and 4: General Index 1. Safety Information
Page 5 and 6: viii) A disconnecting device (switc
Page 7 and 8: 2.2 Dimensional details 2.3 Panel c
Page 9 and 10: 2.5 Panel mounting 2.5.1 Insert the
Page 11 and 12: 3.2 Precautions and advised conduct
Page 13 and 14: 3.3.2 PV control unit D For mA, mV
Page 15 and 16: SX25 mA Output combination 3.3.5 -
Page 17 and 18: 3.3.5 - L Double Action Logic/ Rela
Page 19 and 20: 4.1 Configuration coding The config
Page 21 and 22: 5.1 Keys and display overview 5 Ope
Page 23 and 24: 5.3 Parameter setting 5.3.1 Numeric
Page 25 and 26: 5.3.3 Keypad lock To lock/unlock th
Page 27 and 28: P 33 PpAss Password entry only if C
Page 29 and 30: pass Password entry only if Code va
Page 31 and 32: OC Overshoot control (Automatically
Page 33 and 34: Second group tf ¡l Input filter ti
Page 35 and 36: Analogue control output OP4 r£tr A
Page 37 and 38: Password entry only if Cod£ value
Page 39 and 40: 6 Commissioning Examples When the c
Page 41: First group parameters Press the sc
Page 45 and 46: Second group parameters The display
Page 47 and 48: The self-learning Adaptive Tuning i
Page 49 and 50: Features (at 25°C environmental te
Page 51: Features (at 25°C environmental te

SX25 Series Process Controller - Spirax Sarco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?