Vulcraft_Joist_Catal..

More documents

Recommendations

Info

KCS JOISTS LOAD TABLE (SYSTEME INTERNATIONAL) * MAXIMUM UNIFORMLY DISTRIBUTED LOAD CAPACITY IS 550 PLF AND SINGLE CONCENTRATED LOAD CANNOT EXCEED SHEAR CAPACITY. ** DOES NOT INCLUDE ACCESSORIES 17
METRIC LOAD TABLE OPEN WEB STEEL JOISTS, K-SERIES Based on a Maximum Allowable Tensile Stress of 207 MPa Adopted by the Steel <strong>Joist</strong> Institute May 2, 1994 Revised to May 1, 2000 – Effective August 1, 2002 The black figures in the following table give the TOTAL safe uniformly distributed load-carrying capacities, in kilo- Newtons per meter (kN/m) of K-Series Steel <strong>Joist</strong>s. The weight (kN/m) of the DEAD loads, including the joists, must be deducted to determine the LIVE load-carrying capacities of the joists. Sloped parallel-chord joists shall use span as defined by the length along the slope. The figures shown RED in this load table are the LIVE loads per linear meter of joist which will produce an approximate deflection of L/360 of the span. LIVE loads which produce a deflection of L/240 of the span may be obtained by multiplying the figures in RED by 1.5. In no case shall the TOTAL load capacity of the joists be exceeded. The approximate joist weights, in kiloNewtons per meter (kN/m), shown in these tables do not include accessories. The approximate moment of inertia of the joist, in mm 4 is: I j = 2.6953(W LL )(L 3 )(10 -5 ), where W LL = RED figure in the Load Table: L= (span-102) in millimeters. For the proper handling of concentrated and/or varying loads, see Section 5.5 in the Recommended Code of Standard Practice. Where the joist span exceeds the unshaded area of the load table, the row of bridging nearest the mid-span shall be diagonal bridging with bolted connections at the chords and intersections. 18
Page 2 and 3: TABLE OF CONTENTS **IMPORTANT NOTIC
Page 4 and 5: VULCRAFT OF NEW YORK, INC. LOCATION
Page 6 and 7: JOIST DESIGN COMMENTARY FLOOR VIBRA
Page 8 and 9: LOAD AND RESISTANCE FACTOR DESIGN T
Page 10 and 11: VULCRAFT K SERIES / GENERAL INFORMA
Page 12 and 13: STANDARD LOAD TABLE/OPEN WEB STEEL
Page 14 and 15: STANDARD LOAD TABLE/OPEN WEB STEEL
Page 16 and 17: KCS JOISTS EXAMPLE 2 OPTION A: Use
Page 20 and 21: STANDARD LOAD TABLE IN METRIC UNITS
Page 24 and 25: OPEN WEB STEEL JOISTS, K-SERIES In
Page 26 and 27: OPEN WEB STEEL JOISTS, K-SERIES 4.5
Page 28 and 29: OPEN WEB STEEL JOISTS, K-SERIES NUM
Page 30 and 31: OPEN WEB STEEL JOISTS, K-SERIES 5.9
Page 32 and 33: ACCESSORIES AND DETAILS 2.5K SERIES
Page 34 and 35: ACCESSORIES AND DETAILS K SERIES OP
Page 36 and 37: ACCESSORIES AND DETAILS BRIDGING RE
Page 38 and 39: OPEN WEB STEEL JOISTS, K-SERIES TOP
Page 40 and 41: OPEN WEB STEEL JOISTS, K-SERIES TOP
Page 42 and 43: ACCESSORIES AND DETAILS LH & DLH SE
Page 44 and 45: VULCRAFT LH & DLH SERIES / GENERAL
Page 46 and 47: STANDARD LOAD TABLE/LONG SPAN STEEL
Page 48 and 49: STANDARD LOAD TABLE DEEP LONGSPAN S
Page 50 and 51: METRIC LOAD TABLE LONGSPAN STEEL JO
Page 56 and 57: LONGSPAN AND DEEP LONGSPAN STEEL JO
Page 64 and 65: VULCRAFT SLH / GENERAL INFORMATION
Page 66 and 67: ACCESSORIES AND DETAILS SLH SERIES
Page 68 and 69:
VULCRAFT LOAD TABLE SUPER LONGSPAN
Page 70 and 71:
SPECIFICATIONS FOR VULCRAFT SUPER L
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
VULCRAFT JOIST GIRDERS WHAT ARE JOI
Page 78 and 79:
JOIST GIRDER NOTES If fixed end mom
Page 80 and 81:
MOMENT CONNECTION DETAILS Presented
Page 82 and 83:
DESIGN GUIDE WEIGHT TABLE FOR JOIST
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Based on an allowable tensile stres
Page 92 and 93:
JOIST GIRDERS DESIGN GUIDE WEIGHT T
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
STANDARD SPECIFICATIONS FOR JOIST G
Page 100 and 101:
JOIST GIRDERS For cold-formed secti
Page 102 and 103:
JOIST GIRDERS The designed detail o
Page 104 and 105:
FIRE-RESISTANCE RATINGS WITH STEEL
Page 106 and 107:
FIRE-RESISTANCE RATINGS WITH STEEL
Page 108 and 109:
ECONOMICAL JOIST GUIDE Combined K,
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
RECOMMENDED CODE OF STANDARD PRACTI
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
PUBLICATIONS Vulcraft (Refer to bac
show all

Vulcraft_Joist_Catal..

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?