MODEL NO: GPS NAVIGATION SYSTEM - Zenec

More documents

Recommendations

Info

Action Button(s) Description Zoom preset buttons Tap one of the preset buttons to set the zoom level to a fix, predefined value. Smart Zoom is disabled. These buttons are available in 2D mode. Tap&hold any of the buttons to set its value to the current zoom level, or to reset it to its original value. Tilt and zoom preset buttons Map scale Tap one of the preset buttons to set the tilt and zoom levels to fix, predefined values. Smart Zoom is disabled. These buttons are available in 3D mode. Tap&hold any of the buttons to set its value to the current tilt and zoom levels, or to reset it to its original value. ZENEC Navigation Software shows the scale of the map in 2D mode. 2.2.3 Status information and hidden controls on the map The following information appears in the rounded field in the top left corner, the Turn Preview field. When tapping this area, the result depends on the information currently shown. Icon Information Details Action There is no active route If there is no route to be Tap this area to open Find. navigated, this icon appears in the Turn Preview field. There is no valid GPS If an active route exists, and Tap this area to open the Route Information screen. , position. there is no valid GPS position, the view of the sky above you is shown with coloured dots for each satellite. Some dots need to turn green to be able to navigate. , If the icon is a static picture, route calculation is needed If the icon is animated, route calculation is in progress Next route event (next manoeuvre) GPS position and an active route are available, but automatic off-route recalculation is switched off, and you deviated from the route. ZENEC Navigation Software is calculating or recalculating the route. Tap this area to make ZENEC Navigation Software recalculate the recommended route. Nothing happens if you tap this area of the screen. GPS position and an active Tap this area to open the Route Information screen. route are available, and you navigate the recommended route. This area gives you information about the type and distance of the next route event. 14
The following area appears next to the above described rounded area. When tapping this area, the result depends on the information currently shown. Icon Information Details Action , There is no valid GPS position Traffic restriction Second route event (manoeuvre after the next manoeuvre) Stops the running simulation Route recalculation progress Indicator strip If there is no valid GPS position, this symbol Tap this area to appears here. open the GPS Data screen to check the signal status or the connection settings. When GPS position is available but there is no Nothing route to be navigated, the traffic restriction of the happens if upcoming intersection is shown here if there is you tap this any. area of the screen. When GPS position and an active route are both Tap this area to available, this field shows the route event that follows the next route event shown in the above open the described area. Itinerary screen with the turn by turn guidance instructions . Tap this This icon appears during Route Simulation. area to stop the simulation. During route recalculation, this field shows the Nothing recalculation progress between 0% and 100%. happens if you tap this area of the screen. Nothing - sounds muted/enabled happens if - TMC status you tap this area of the screen. The following symbols appear in the Indicator strip: Icon Description The sound output of ZENEC Navigation Software is muted. The sound output of ZENEC Navigation Software is enabled. No TMC receiver is connected or TMC is turned off. 15
Page 1 and 2: MODEL NO: ZE-DVBT10 1 CH DVB-T TUNE
Page 3 and 4: Thank you for choosing ZENEC Naviga
Page 5 and 6: 3.2 Creating a multi-point route (i
Page 7 and 8: 1 Warnings and Safety information Z
Page 9 and 10: Tasks Instructions Shortcut to op
Page 11 and 12: Task Entering a space, for example
Page 13: Action Button(s) Description 3D map
Page 17 and 18: 2.2.4 Using the Cursor (the selecte
Page 19 and 20: 2.3.2.3 Selected location (Cursor)
Page 21 and 22: When you are on the Map screen, you
Page 23 and 24: Note! TMC is not a global service.
Page 25 and 26: 3.1.2 Entering an address or part o
Page 27 and 28: 4. Enter the street name: 1. Tap .
Page 29 and 30: 3. Get to the list of search result
Page 31 and 32: Tap to open the list of results bef
Page 33 and 34: 5. Tap the desired POI in the list.
Page 35 and 36: 3.4 Editing the route Tap the follo
Page 37 and 38: 3.10 Loading a saved route The proc
Page 39 and 40: Symbol Name Action Trip data Opens
Page 41 and 42: 4.1.1.1 GPS position quality indica
Page 43 and 44: 4.1.2.2 3D object types To enable o
Page 45 and 46: In order to show a part of the map
Page 47 and 48: You have the following data and fun
Page 49 and 50: Most of the fields on this screen h
Page 51 and 52: Icon Colour Name Description Red ZE
Page 53 and 54: 4.4.1 Manage Saved Routes You can m
Page 55 and 56: 4.4.4 Manage Favourites You can man
Page 57 and 58: Button Description Building Visib
Page 59 and 60: Road Types Used for Route Planning:
Page 61 and 62: Button Background Description You c
Page 63 and 64: 5 Glossary 2D/3D GPS reception The
Page 65 and 66:
6 End User Licence Agreement 1 The
Page 67 and 68:
9 Sanctions 9.1 The Licensor hereby
show all

MODEL NO: GPS NAVIGATION SYSTEM - Zenec

Create successful ePaper yourself

Delete template?

Save as template?