Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Machine description Machine control – Operating elements 4.2 Machine control – Operating elements NOTE Machine control provides the user with up to 8 welding tasks (JOBs). JOB 0 represents manual operating mode. This is where you can change/optimise all parameters directly in machine control (see chapter "Operating concepts"). COMFORT S 6 AMP VOLT JOB S 7 AMP% sec 8 sec AMP 5 sec AMP% 4 sec 1 AMP% Puls 2 Automatic sec kHz 3 sec AMP JOB kHz % sec Figure 4-3 Item Symbol Description 0 1 Welding process button MMA welding, lights up in green / arcforce setting, lights up in red TIG welding 2 Operating mode button spotArc (spot time setting range 0.01 sec. to 20.0 sec.) 3 4 Puls Automatic sec kHz Non-latched Latched TIG pulses key button TIG automated pulses (frequency and balance) sec kHz TIG pulses with times, lights up in green / Fast TIG DC pulses with frequency and balance, lights up in red Display changeover button Welding current display Welding voltage display JOB number display 18 Item No.: 099-000097-EWM01
Machine description Machine control – Operating elements Item Symbol Description 0 5 Welding parameter setting rotary dial Setting all parameters such as ignition, welding, end current, gas pre-flow and gas post-flow times, pulse edges, etc. 6 Three-figure LED display Welding parameter display (see also chap. “Welding data display”). 7 Error/status indicators Collective interference signal light (see Operating problems chapter) S S Water deficiency signal light (welding torch cooling) Excess temperature signal light safety sign signal light 8 Function sequence (see next chapter) Item No.: 099-000097-EWM01 19
Page 1 and 2: EWM HIGHTEC WELDING GmbH Dr. Günte
Page 3 and 4: Machine and Company Data Please ent
Page 5 and 6: Contents Notes on the use of these
Page 7 and 8: Contents Notes on the use of these
Page 9 and 10: Safety instructions Notes on the us
Page 11 and 12: Safety instructions General WARNING
Page 13 and 14: Safety instructions Transport and i
Page 15 and 16: 3 Technical data 3.1 TETRIX 180 COM
Page 17: Machine description TETRIX 180 COMF
Page 21 and 22: Machine description Machine control
Page 23 and 24: Functional characteristics Operatin
Page 45 and 46: Functional characteristics MMA weld
Page 47 and 48: Functional characteristics Remote c
Page 49 and 50: Functional characteristics Advanced
Page 51 and 52: Functional characteristics Advanced
Page 53 and 54: Functional characteristics Interfac
Page 55 and 56: Functional characteristics Menus an
Page 57 and 58: Functional characteristics Menus an
Page 59 and 60: Commissioning Area of application -
Page 61 and 62: 6.7 TIG welding 6.7.1 Welding torch
Page 63 and 64: Commissioning TIG welding 6.7.4.1 C
Page 65 and 66: Commissioning MMA welding • Inser
Page 67 and 68: Maintenance and testing Test 7.3 Te
Page 69 and 70:
Maintenance and testing Test 7.3.6
Page 71 and 72:
Maintenance and testing Disposing o
Page 73 and 74:
Warranty Warranty Declaration 8.2 W
Page 75 and 76:
Operating problems, causes and reme
Page 77 and 78:
9.4 General operating problems Oper
Page 79 and 80:
Circuit diagrams TETRIX 180 COMFORT
Page 81:
12 Appendix A 12.1 Declaration of C
show all

Operating instructions - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?