Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Functional characteristics Advanced settings 5.5.5 Ramp function foot-operated remote control RTF 1 0 1 0 1 Figure 5-20 Display Setting/selection Exit the menu Exit Machine configuration Settings for machine functions and parameter display Ramp function Remote control RTF 1 The ramp function can be switched on and off Switch on Switching on machine function Switch off Switching off machine function 52 Item No.: 099-000097-<strong>EWM</strong>01
Functional characteristics Interfaces for automation 5.6 Interfaces for automation 5.6.1 Remote control connection socket, 19-pole CAUTION Damage to the machine due to improper connection! Unsuitable control leads or incorrect connection of input and output signals can cause damage to the machine. • Only use shielded control leads! • If the machine is to be operated with control voltages connection via suitable isolation amplifiers is required! • To control the main or secondary current via control voltages, the relevant inputs must be enabled (see specification for activation of control voltage). 10V A B L F 1 2 2 3 I>0 C D E 4 5 0-10V 0-10V 10-100K 10-100K T B A M 0V J 6 D C E N P U V R T S F H G L J K +15V (max. 75mA) -15V (max. 25mA) U K V R S H 6 7 8 9 10 START / STOP AMP / AMP% (PULS) M N P 11 G 12 I SOLL (1V=100A) Figure 5-21 Pos. Pin Signal shape Designation 1 A Output Connection for cable screen (PE) 2 B/L Output Current flows signal I>0, galvanically isolated (max. +- 15V/100mA) 3 F Output Reference voltage for potentiometer 10V (max. 10mA) 4 C Input Control value specification for main current, 0-10V (0V = I min , 10V = I max ) 5 D Input Control value specification for secondary current, 0-10V (0V = I min , 10V = I max ) 6 J/U Output Reference 0V 7 K Output Power supply +15V, max. 75mA 8 V Output Power supply -15V, max. 25mA 9 R Input Start/Stop welding current 10 S Input Switching between MMA and TIG welding 11 H Input Switching between main and secondary welding currents (pulses) 12 M/N/P Input Activation of control voltage specification Set all 3 signals to reference potential 0V to activate external control voltage specification for main and secondary currents 13 G Output Measured value I SETPOINT (1V = 100A) Item No.: 099-000097-<strong>EWM</strong>01 53
Page 1 and 2: EWM HIGHTEC WELDING GmbH Dr. Günte
Page 3 and 4: Machine and Company Data Please ent
Page 5 and 6: Contents Notes on the use of these
Page 7 and 8: Contents Notes on the use of these
Page 9 and 10: Safety instructions Notes on the us
Page 11 and 12: Safety instructions General WARNING
Page 13 and 14: Safety instructions Transport and i
Page 15 and 16: 3 Technical data 3.1 TETRIX 180 COM
Page 17 and 18: Machine description TETRIX 180 COMF
Page 19 and 20: Machine description Machine control
Page 21 and 22: Machine description Machine control
Page 23 and 24: Functional characteristics Operatin
Page 45 and 46: Functional characteristics MMA weld
Page 47 and 48: Functional characteristics Remote c
Page 49 and 50: Functional characteristics Advanced
Page 51: Functional characteristics Advanced
Page 55 and 56: Functional characteristics Menus an
Page 57 and 58: Functional characteristics Menus an
Page 59 and 60: Commissioning Area of application -
Page 61 and 62: 6.7 TIG welding 6.7.1 Welding torch
Page 63 and 64: Commissioning TIG welding 6.7.4.1 C
Page 65 and 66: Commissioning MMA welding • Inser
Page 67 and 68: Maintenance and testing Test 7.3 Te
Page 69 and 70: Maintenance and testing Test 7.3.6
Page 71 and 72: Maintenance and testing Disposing o
Page 73 and 74: Warranty Warranty Declaration 8.2 W
Page 75 and 76: Operating problems, causes and reme
Page 77 and 78: 9.4 General operating problems Oper
Page 79 and 80: Circuit diagrams TETRIX 180 COMFORT
Page 81: 12 Appendix A 12.1 Declaration of C

Operating instructions - EWM Hightec Welding GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?