tors actuators - Norgren Pneumatics. Motion Control Equipment ...

ACTUATORS
Series N Actuators
1-1/8" to 4" bore sizes
40 (178)
35 (156)
30 (133)
25 (111)
20 (89)
15 (67)
10 (44)
5 (22)
4" Bore
3 1 /4" Bore
2 1 /2" Bore
2" Bore
1 1 /2" Bore
1 1 /8" Bore
Transverse Loads
Load
0 (0)
POUNDS 0 5 10 15 20 25 30 35 40
(NEWTONS)
(0) (127) (254) (381) (508) (635) (762) (889) (1016)
STROKE INCHES (mm)
The transverse and torsional load
graphs shown are to be utilized as a
guideline with respect to the
maximum load and stroke of each
bore size.
NOTE: For strokes or loads not listed
consult factory.
Transverse or torsional loads placed
on the cylinder will cause some
deflection of the piston rods.
Excessive deflection will adversely
affect cylinder life and should be
considered at the time of initial
application design.
TORQUE
INCH POUNDS
(NEWTON METERS)
80 (9.0)
75 (8.5)
70 (7.9)
65 (7.3)
60 (6.8)
55 (6.2)
50 (5.6)
45 (5.1)
40 (4.5)
35 (4.0)
30 (3.4)
25 (2.8)
20 (2.3)
15 (1.7)
10 (1.1)
5 (.56)
0 (0)
4" Bore
3 1 /4" Bore
2 1 /2" Bore
2"
Bore
1 1 /2"
Bore
1 1 /8"
Bore
Torsional Loads
Load
Load
0 5 10 15 20 25 30 35
(0) (127) (254) (381) (508) (635) (762) (889)
STROKE INCHES (mm)
Basic Actuator 01 (MX0)
1
P 1 *
MM Rod ∅
B Bushing ∅
Y
P + Stroke
EE NPT Port
Each End
D
4 2 E Sq.
DD Tap
BB Deep
4 Places
*Head Port is off center on
vertical rod axis with
port in position 1 or 3,
horizontal rod axis with
port in position 2 or 4.
.031 x 45°
Chamfer
3
GS∅
A
AC
C
F
V
G
ZB + Stroke
LB + Stroke
J
RE Sq.
KK Tap B 1
Deep 4 Places
BM∅
HD Across Flats
N
RG
Standard Tooling Plate
(Included with Cylinder)
Bore A AC B B1 BB BM C D DD E EE F G GS
1-1/8" 0.625 1.25 N/A 0.5 0.188 0.27 0.625 0.627 10 – 32 1.5 1/8 0.25 .875 0.19
1-1/2" 0.625 1.5 0.59 Thru 0.312 0.33 0.875 0.75 1/4 – 28 2 1/4 0.375 1.5 0.25
2" 0.75 1.5 0.9 Thru 0.312 0.55 0.75 1.052 5/16 – 24 2.5 1/4 0.375 1.5 0.5
2-1/2" 0.75 1.75 0.9 Thru 0.312 0.55 1 1.398 5/16 – 24 3 1/4 0.375 1.5 0.5
3-1/4" 1.25 1.75 1.498 Thru 0.437 0.9 0.5 2 3/8 – 24 3.75 3/8 0.625 1.75 0.75
4" 1.25 1.75 1.498 Thru 0.437 0.9 0.5 2.36 3/8 – 24 4.5 3/8 0.625 1.75 0.75
Bore HD J KK LB MM N P P1 RE RG TT TZ V Y ZB
1-1/8" 0.25 0.625 6 – 32 2.25 0.312 0.4 1.469 0.241 1.125 0.58 0.75 1.25 N/A 2.031 3.75
1-1/2" 0.312 1 10 – 32 3.625 0.375 0.4 2.125 0.303 1.428 0.58 1.125 1.5 0.25 2.875 5.5
2" 0.5 1 1/4 – 28 3.625 0.625 0.526 2.125 0.48 1.84 0.705 1.43 2 0.25 2.875 5.5
2-1/2" 0.5 1 5/16 – 24 3.75 0.625 0.526 2.25 0.635 2.192 0.705 1.84 2.5 0.25 3.125 5.875
3-1/4" 0.812 1.25 3/8 – 24 4.25 1 0.784 2.625 0.845 2.758 1.205 1.79 3.25 0.25 3.437 6.625
4" 0.812 1.25 3/8 – 24 4.25 1 0.784 2.625 0.875 3.323 1.205 3.44 4 0.25 3.437 6.625
Cylinder with 20 (not NFPA) Base Bar
Cylinder with 02 Bottom Tap
SB Holes
4 Places
TT Sq.
TZ Sq.
A
ST
SW
TS
US
Bore F G LB SB SS ST SU SW TS US XS
1-1/8" 0.25 1 2.25 0.203 1.75 0.25 0.75 0.25 1.875 2.375 1.75
1-1/2" 0.375 1.5 3.625 0.437 2.875 0.25 1.125 0.375 2.75 3.5 2.25
2" 0.375 1.5 3.625 0.437 2.875 0.25 1.125 0.375 3.25 4.0 2.25
2-1/2" 0.375 1.5 3.75 0.437 3 0.375 1.125 0.375 3.75 4.5 2.5
3-1/4" 0.625 1.75 4.25 0.563 3.25 0.5 1.25 0.5 4.75 5.75 2.875
4" 0.625 1.75 4.25 0.563 3.25 0.5 1.25 0.5 5.5 6.5 2.875
ACT-58
SH
XS
SU
SS + Stroke
SU
SW
TN
XT SN + Stroke NT Tap
TK Deep
4 Places
Bore NT SN TK TN XT
1-1/8" 10 – 32 1.5 0.25 0.5 2
1-1/2" 1/4 – 20 2.25 0.375 0.625 2.812
2" 5/16 – 18 2.25 0.375 0.875 2.812
2-1/2" 3/8 – 16 2.375 0.625 1.25 3.063
3-1/4" 1/2 – 13 2.625 0.625 1.5 3.437
4" 1/2 – 13 2.625 0.75 2.063 3.437
Norgren.com/usa – 303.794.2611 – help@amer.norgren.com