0870 849 8057 USERS G 24, 30 - Ideal Heating

More documents

Recommendations

Info

INsTaLLaTION 22 1. INTERNaL TO sINK WasTE UpsTREaM OF sINK WasTE TRap INsTaLLaTION 22 CONDENsaTE pIpE TERMINaTION CONFIgURaTIONs notes: all exTernal pipe runs MusT be in accorDance WiTh bs 6798 3. INTERNaL CONNECTION TO sOIL aND VENT sTaCK * Make connection to SVP using a solvent welded saddle 4. TERMINaTION TO sOaK aWay 5. TERMINaTION TO DRaIN / gULLy BOILER cla7774 External wall minimum 500mm BOILER cla7771a Termination to Soak away BOILER esp8882 Ground Level BOILER cla7775 External wall DRAIN DRAIN Open end of pipe direct into gulley below grating but above water level Ground Level Open end of pipe direct into gulley below grating but above water level Ground Level i-mini - Installation and Servicing
i-mini - Installation and Servicing INsTaLLaTION 23 CONNECTINg ThE FLUE TO ThE BOILER Notes. • Before fitting the flue turret fill the condensate trap within the boiler by pouring a cupful of water into the flue outlet (shown below). Take care to ensure that the water is only poured into the flue outlet, and does not spill into the boiler casing. • During assembly check that flue seals do not become dislodged. 1. Ensure front panel is removed. Refer to Frame 7. 2. Locate the flue into the turret. 3. Insert the flue assembly through the prepared hole in the wall. Push through and pull back to seal against outside wall face. 4. Ensure rubber flue seal is present & fully engaged into plastic top flue manifold then locate the flue turret into the flue manifold and secure by applying downward pressure. 5. Engage the clamp in its slide mechanism and push it horizontally backwards 6. Locate BOTH plastic pegs BEFORE the front retaining clip is fully located. Note - Flues over 1 metre long It is recommended that a support bracket is fitted for every 1 metre of extension pipe used and a bracket should be used at every joint, to ensure pipes are held at the correct angle. 5 3G9847d 4 noTe. siDe Flue Select the orientation before inserting turret into boiler flue manifold. DO NOT twist the turret once inserted. 2 3G9847a 3 Retaining Clip (assembled) Flue Outlet 6 3G9847b 205367-9847d 3G9847e 10120-205367 Plastic Pegs (assembled) 23 FLUE OUTLET
Page 1 and 2: INSTALLATION AND SERVICING 24, 30 F
Page 3 and 4: FOR aNy TEChNICaL qUERIEs pLEsE RIN
Page 5 and 6: i-mini Natural gas only Boiler size
Page 7 and 8: saFETy Current gas safety (installa
Page 9 and 10: aIR sUppLy It is NOT necessary to h
Page 11 and 12: general 1. The installation must co
Page 13 and 14: INsTaLLaTION 5 BOILER assEMBLy - Ex
Page 15 and 16: 7 FRONT paNEL REMOVaL 1. Loosen the
Page 17 and 18: 11 WaLL MOUNTINg TEMpLaTE i-mini -
Page 19 and 20: i-mini - Installation and Servicing
Page 21: 19 FITTINg ThE WaLL MOUNTINg pLaTE
Page 25 and 26: 26 FLUE TERMINaL pOsITION The termi
Page 27 and 28: 28 CONNECTIONs & FILLINg CH Flow i-
Page 29 and 30: 32 WIRINg DIagRaM PCB KEY b - blue
Page 31 and 32: 34 INITIaL LIghTINg Legend a. Pre-h
Page 33 and 34: 36 REsET pROCEDURE 37 haNDINg OVER
Page 37 and 38: 43 CLEaNINg ThE hEaT ExChaNgER note
Page 39 and 40: 47 BURNER INJECTOR REpLaCEMENT 1. R
Page 43 and 44: 1. Refer to Frame 45. Note: Ensure
Page 45 and 46: 59 DRaININg ThE BOILER CH Flow 60 p
Page 49 and 50: 69 FLOW ThERMIsTOR REpLaCEMENT 1. R
Page 53 and 54: 78 aLTERNaTINg ‘F’ aND ‘2’
Page 55 and 56: 83 aLTERNaTINg ‘F’ aND ‘9’
Page 57 and 58: 88 NO hW BUT Ch ON Does the display
Page 61 and 62: Gas Safe Register Number Gas Safe R

0870 849 8057 USERS G 24, 30 - Ideal Heating

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?