2012 e-catalog - STIL

More documents

Recommendations

Info

Non-contact «point» sensors SELECTION GUIDE SENSORS STIL Initial: Technical specifications Controllers STIL initial Series Model STIL Initial 0.4 STIL Initial E1.2 STIL Initial E1.2 /90 (1) STIL Initial 4.0 STIL Initial 12 OPTICAL PEN (PROBE) Model CL2-MG140 ENDO 1.2 ENDO 1.2/90 (1) CL4-MG35 CL5-MG35 Measuring Range 0.4 mm 1.2 mm 1.2 mm 4.0 mm 12.0 mm Working Distance 11.0 mm 2.4 mm 0.4 mm 16.4 mm 29 mm Spot Diameter 3.4 µm 15 µm 13 µm 7.2 µm 16.5 µm Max. Slope Angle (2) (3) +/- 28° +/- 14° +/- 9° +/- 21° +/- 14° Weight 190 g 10 g 10g 155 g 175 g Dimensions x L 27mm x 208.9mm 6 mm x 75.2 mm 6 mm x 82 mm 27 mm x 145.5 mm 27 mm x 145.5 mm Distance Measurement Axial Resoluton (4) - With no averaging - With Averaging 10 22 nm 8 nm 100 nm 35 nm 160 nm 60 nm 130 nm 50 nm 400 nm 180 nm Accuracy (5) 80 nm 300 nm 800 nm 300 nm 900 nm Measuring rough metalic samples (9) R NR NR NR NR Roughness measurement (10) Min. measurable Ra 30nm NR NR NR NR 3D SYSTEMS SPECTRO COLORIMETERS GONIO PHOTOMETERS Thickness Measurement (6) Min. Measurable Thickness (7)(8) 16 µm 75 µm NA 110 µm 450 µm Max. Measurable Thickness (7)(8) 510 µm 1600 µm NA 5700 µm 16500 µm CONTROLLER BOX Measuring Modes Measuring Rate Digital Outputs Digital Resoluton Synchronizaton Advandced Features Power supply / Consumpton Weight Dimensions W x H x D FIBER OPTICS CABLE «Distance» and «Thickness» 100 Hz to 2000Hz USB 2.0 and RS232 (up to 460800 baud) In «Distance» mode: 30 bits In «Thickness» mode: 15 bits Input and Output 0V - 5V TTL synchronizaton signals Extensive trigger capacites «Double frequency» mode «Auto LED» mode «First peak» mode «Hold last value» mode «Thickness calibraton» 100V to 240 V AC 50-60 Hz / 25W 1920 g 199 mm x 123.5 mm x 277 mm (1) Radial (90°) measuring optcal pen. (2) The maximal angular slope applies to specular (mirror-like) surfaces only. For Diffusing surfaces the maximal slope angle is higher (up to 87° for perfect diffusers). (3) Measured on a mirror at 100 Hz, with no averaging. (4) Axial resoluton is defined as the RMS Noise level measured at optmal rate on a statc sample located at the center of the measuring, with no averaging. (5) Accuracy is defined as the max. error over the entre measuring range, measured immediately after distance calibraton at the following conditons: “Auto-adaptve LED” mode, optmal rate, slope angle=0°, averaging factor= measuring rate/10. (6) For obtaining metrological performances in this mode it is recommended to carry out a calibraton on a thickness standard. (7) These values are for a refractve index of 1.5 (for measuring air gap thickness divide by 1.5). (8) Typical values, measured at the center of the measuring range at optmal rate, with no averaging. (9) R = Recommended for measuring rough metallic samples (these samples can be measured with full performances) NR = Not recommended for measuring rough metallic samples (these samples may be measured, but with reduced performances) (10) The precise value of the min measurable Ra depends on the characteristcs of the sample. The values given in the table are typical.. N.B. : the values are subject to change without notce. 12 www.stlsa.com E1204
SELECTION GUIDE SPECTRO COLORIMETERS GONIO PHOTOMETERS SENSORS 3D SYSTEMS Non-contact «point» sensors Configurable Chromatic Confocal «point» sensors These sensors measure the alttude (z coordinate) of the sample point located on their optcal axis. They can also measure the thickness of transparent samples. They consist of a controller (1), an «optcal pen» (optcal probe) (2) and a fiber optc cable (3). 2 controller lines (CCS & CHR), 3 optcal pen lines (CL-MG, OP & ENDO) and different fiber optc cable models are available. A single controller may be ordered with several interchangeable optcal pens. (1) (3) (2) Advantages - Select the CCS or CHR controller, as well as the optcal pen and the fiber optcs cable best suited for your applicaton. - Large choice of measuring ranges (110 µm - 20 mm), - Large choice of optcal pens satsfying specific requirements («endoscopic» / radial pens / large working distance / steep slope / small spot size / through-window measurement..) The CCS controller line 3 controllers for configurable chromatc confocal sensors featuring different number of channels are available: - the CCS PRIMA (1 channel), CCS PRIMA 2 (2 channels) and CCS PRIMA 4 (4 channels). Advantages - High precision, high resoluton, - Compatble with all chromatc confocal optcal pens, - Up to 20 different optcal pens interchangeable on the same controller, - Digital and analog outputs, - Synchronized reading of external digital encoders. CCS PRIMA controllers - The leading chromatic confocal sensor worldwide, - The most sophisticated chromatic confocal sensor on the market, - Recommended for OEM User and Industrial applicatons, - Improved performances in thickness mode thanks to a specific Thickness calibraton, - Long lifetme light source, - Measuring rates: 100 Hz to 2000 Hz. E1204 www.stlsa.com 13
Page 1 and 2: NON CONTACT MEASUREMENT SOLUTIONS S
Page 3 and 4: SELECTION GUIDE SENSORS 3D SYSTEMS
Page 9 and 10: SELECTION GUIDE SPECTRO COLORIMETER
Page 11: SELECTION GUIDE SPECTRO COLORIMETER
Page 63 and 64:
SELECTION GUIDE SPECTRO COLORIMETER
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
show all

2012 e-catalog - STIL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?