Navigate the Catalog HYDRAFORCE

COILS AND ELECTRONIC CONTROLS
Proportional Valve Controller—Metal Housing—
CONNECTIONS/ADJUSTMENTS
Dual Solenoid Multifunction Valve Driver
Dither
Adjustments
CW to Increase
DITHER
LEVEL
0–10%
or rated
I-Max.
DITHER
FREQUENCY
70–350 Hz
Power Input
+9–32 VDC
Ground
Control Inputs
+
GND
POWER
9...32V
SW1 SETTINGS
SW2 SETTINGS
5 SELECTS I or V INPUT SYM RAMPS
1–ON ±10V
SOL A: 1–ON 2–OFF
2–ON ±5V or ±20mA
SOL B: 3–ON 4–OFF
NON-SYM RAMPS
3–ON 0–10V
SOL A: 1–OFF 2–ON
4–ON 0–5V or 0–20mA SOL B: 3–OFF 4–ON
5–ON=I OFF=V
JOYSTICK DEADBAND
5–ON=NO DEADBAND
5–OFF=DEADBAND
DITHER
LEVEL
DITHER
FREQUENCY
DUAL SOLENOID DRIVER
P/N: 40XXXXX
SAH
SAL
SBH
SBL
PROPORTIONAL
OUTPUT
Proportional
Outputs
Solenoid Ap (High)
Solenoid Ap (Low)
Solenoid Bp (High)
Solenoid Bp (Low)
Digital Outputs
Signal
In
SGND
IN
Ad+
Ad–
Ad+
Ad–
Disable
I-Max/2
Signal
+10V Ref.
+2.5V Ref.
DISABLE
I-MIN-A I-MAX-A I-MIN-B I-MAX-B
I-MAX/2 A-UP A-DOWN B-UP B-DOWN
SGND
+10V REF
+2.5V REF
Bd+
Bd–
ABd+
ABd–
Cd+
Bd+
Bd–
ABd+ Pump Enable
ABd– Pump Enable
Cd+ Latching
+5V Ref.
INPUT
+5V REF
ON
OFF
ON
1 2 3 4 5
ON
1 2 3 4 5
ON
OFF
DIGITAL
OUTPUT
Cd–
Cd– Latching
1 2 3 4 5 1 2 3 4 5
SWITCH 1 SWITCH 2
INPUT SELECTION OPTIONS
Current=ON
Voltage=OFF
0–5VDC or 0–20mA
0–10VDC
±5VDC or ±0–20mA
±10VDC
Settings
shown are for
0–10VDC input
ON
OFF
ON
1 2 3 4 5
ON
1 2 3 4 5
1 2 3 4 5 1 2 3 4 5
SWITCH 1 SWITCH 2
SOLENOID 'A' RAMPS
Symmetrical: 1=ON, 2=OFF
Non-Symmetrical: 1=OFF, 2=ON
SOLENOID 'B' RAMPS
Symmetrical: 3=ON, 4=OFF
Non-Symmetrical: 3=OFF, 4=ON
JOYSTICK DEADBAND
No Joystick Deadband: 5=ON
Joystick Deadband: 5=OFF
ON
OFF
Settings shown are for
Symmetrical Up and
Down Ramps for
Solenoids 'A' and 'B'.
Electronic Deadband
is selected for Joystick
Input or Control Signal.
Proportional Adjustments
0–2.0 amps or 0–300 mA
CW to Increase
I-MIN-A I-MAX-A I-MIN-B I-MAX-B
Ramp Time Adjustments
0.01 to 5 seconds
CW to Increase
A-UP A-DOWN B-UP
B-DOWN
3.540.3