Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

STEP 3 NOTE THE SEVEN-INCH DISTANCE FROM THE EAVE OF THE BIN TO THE CENTER LINE OF THE HOLES IN THE TRACK. Bins with steeply-pitched roofs may allow the 7" distance to be reduced. Roofs with the low or “flat” profiles may require more clearance. Reinforcements for the roof or inner ladders which might interfere with the movement of the Stir-Ator should be trimmed off as indicated in Drawing A on page 33. If this cannot be done, the 7" distance from the eave to the bolt holes must be incresed proportionately. STEP 4 There should be slightly more track material than is required. Upon making the complete circuit of the bin, the end of the last section should be cut off so as to fit snugly against the forward end of the first length and a 7/16" hole drilled, 5/8" from the cut-off end. ALL TRACK JOINTS SHOULD BE ALIGNED AS SMOOTHLY AS POSSIBLE. Mis-alignment should be corrected by filing or bending, if necessary. STEP 5 Because the Stir-Ator augers run very close to the bin wall, INSIDE WALL LADDERS MUST BE MOUNTED VERY CLOSE TO THE BIN WALL. If this cannot be accomplished, the ladder must be removed. A portable ladder is advised, and this can be obtained form your dealer. If the walk in door protrudes over 2-1/2" into the bin itself, SKID PLATES SHOULD BE PUT ON THE DOOR so that the augers will not get caught during Stir-Ator operation. Photo 1 STEP 6 At this time, hook the three suspension chain hooks over the top edge of the fill hole. Space them equally around the fill hole. See Drawing B on page 36 or Photo 1. STEP 7 Install the switch box above the inspection hole. Be sure the Red Giant will not hit it, and do not forget the brace. See Photo 1 or Drawing A on page 33. Lead-in cord and shut-off chain need to be positioned so that the Stir-Ator will not catch them as it rotates around the bin. NOTE THE CLEARANCE REQUIREMENTS IN DRAWING A AND B. 14 PNEG-1358 Red Giant Stir-Ator
CHAIN IDLER SUPPORT BRACKETS STEP 8 Put main frame on saw horses (two pieces), as shown in Photo 2. Then space about 11-1/2 inches apart with angle flanges outward. Be sure chain idler support brackets are on the same end. Photo 2 STEP 9 Place inboard pivot end over main frame as shown in Photo 3. Be sure inboard pivot is on the same end of the frame as chain idler support brackets. See Photo 5 on page 16. Have the heavy electric cords coming out of the center pivot on the same side as the loops on the main frame. These loops hold the heavy cords in place. Large loops for both rubber covered cords, small loops on opposite end of frame for 14-3 cord only. Using two 3/8" x 1" hex head bolts, place flat washer onto bolt, put bolt through yoke and frame, and secure with lock-washer and nut on inside of frame angle (Two on each side). Using two 3/8" x 1" hex head bolts for four-auger machine (Two 3/8" x 2" hex head bolts for six-auger machine), bring bolts up from the bottom of the main frame through yoke and secure with flat washer, lock-washer, and nuts (Two on each side). See Photo 3 or Drawing E on page 44. Photo 3 PNEG-1358 Red Giant Stir-Ator 15
Page 1: OWNER’S MANUAL Red Giant Grain St
Page 4 and 5: SAFETY GUIDELINES This manual conta
Page 6 and 7: PRACTICE SAFE MAINTENANCE Always di
Page 8 and 9: FINAL INSPECTION CHECK LIST 1. HAVE
Page 10 and 11: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 12 and 13: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 16 and 17: STEP 10 Place the outboard pivot en
Page 18 and 19: STEP 13 Place the 3/4" x 14" axle s
Page 20 and 21: STEP 17 Bolt the drive guide arm on
Page 22 and 23: STEP 21 Installation of gearbox dri
Page 24 and 25: STEP 22 Installation of gearbox con
Page 26 and 27: Accelerometer lead wire Power-out w
Page 28 and 29: STEP 27 Place all belt shields as s
Page 30 and 31: to the shut-off chain so that it wi
Page 32 and 33: The augers are manufactured to allo
Page 34 and 35: NOTES 34 PNEG-1358 Red Giant Stir-A
Page 36 and 37: Red Giant Stir-Ator Overall Dimensi
Page 38 and 39: 4 - 6 Auger Shields and Electrical
Page 40 and 41: 4 - 6 Auger Trolley Base Unit Model
Page 42 and 43: Outboard Pivot End and Track Sectio
Page 44 and 45: Center Inboard Pivot End Model 176
Page 46 and 47: 6-AUGER TROLLEY EXTENSION DRAWING F
Page 48 and 49: RED GIANT WIRING DIAGRAMS Single Ph
Page 50 and 51: Three Phase - 460 Volt 50 PNEG-1358
Page 52 and 53: Three Phase - 380 Volt 52 PNEG-1358
Page 54 and 55: RED GIANT 460 VOLT TRANSFORMER HOOK
Page 56 and 57: DRAWING K DRAWING L 56 PNEG-1358 Re
Page 58 and 59: PINION SHAFTS DMC # Model # Year Fi
Page 60 and 61: GEARBOX #129 (104B2134) 104B2134 #1
Page 62 and 63: GEARBOX #150 (104B2135) 104B2135 #1
Page 64 and 65:
RED GIANT TRACK DRIVE GEAR MOTOR GE
Page 66 and 67:
DRYING RECOMMENDATIONS To get unifo
Page 68 and 69:
STIR-GUARD OPERATION The Stir-Guard
Page 70 and 71:
MAINTENANCE and ADJUSTMENTS (cont
Page 72 and 73:
RED GIANT TROUBLE SHOOTING ELECTRIC
Page 74 and 75:
RED GIANT TROUBLE SHOOTING TRACK UN
Page 76 and 77:
NOTES 76 PNEG-1358 Red Giant Stir-A
Page 78:
Red Giant Grain Stir-Ator Model 176
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?