Outboard Pivot End and Track Section Model 176 "<strong>Red</strong> <strong>Giant</strong>" <strong>Stir</strong>ator DRAWING D 42 PNEG-1358 <strong>Red</strong> <strong>Giant</strong> <strong>Stir</strong>-<strong>Ator</strong>
Outboard Pivot End and Track Section Ref. No. Part No. No. Req'd Description Ref. No. Part No. No. Req'd Description 1 106C074 As Req'd Track - Bin Wall - 16' Length 33 1EL0361 1 Outlet Box, 4" x 4" 2 3 4 103C0038 106C063 104C0017 As Req'd As Req'd 1 Track <strong>Co</strong>nnector Plate Track Bracket - Bin Wall, Galv. Tilt Switch Holder 34 35 36 1EL0410 401176 1EL0727 1 2 2 <strong>Co</strong>nnector, 1/2" MPT Wire Twist <strong>Co</strong>nnector Fuse - Gear Motor 220V 5,6,7,8 Rails 37 S-1429 5 Hex Bolt, 1/4"-20 x 3/4" DAVID0533 DAVID0509 DAVID0536 DAVID0512 DAVID0537 DAVID0513 DAVID0539 DAVID0515 DAVID0541 DAVID0517 Front Rail Rear Rail Front Rail Rear Rail Front Rail Rear Rail Front Rail Rear Rail Front Rail Rear Rail 142" Long 24' 4 Auger 160" Long 27' 4 Auger 165" Long 27' 10" 4 Auger 178" Long 30' 4 Auger 196" Long 33' 4 Auger 39 40 41 42 43 44 45 46 47 48 106E110 S-6781 S-4310 S-6493 S-396 S-456 2FH0426 S-8059 S-9094 S-1101 1 1 9 1 As Req'd 12 1 As Req'd As Req'd 5 1.8 Amp. Kit, PCB and Accelerometer Asm - Elec Tilt Switch Wing Nut - Self Locking, 1/4" Hex Lock Nut, 1/4" Hex Lock Nut, 1/2" Hex Nut, 5/16" Hex Nut, 3/8" Wing Thumbscrew, 1/4" x 1-1/2" Carriage Bolt, 5/16" x 1" Carriage Bolt, 5/16" x 3" Grade 5 Hex Bolt, 1/4" x 1/2" DAVID0552 Front Rail 49 S-7520 12 Hex Bolt, 3/8" x 1" (4 Auger) 214" Long 36' 4 Auger DAVID0549 Rear Rail S-7520 8 Hex Bolt, 3/8" x 1" (6 Auger & 36' 4 Auger) DAVID0553 Front Rail 50 S-7522 4 Hex Bolt, 3/8" x 2" (6 Auger or 36' 4 Auger) 247" Long 42' 4 Auger DAVID0550 Rear Rail 51 S-7532 1 Hex Bolt, 1/2" x 3-1/2" DAVID0542 Front Rail 52 3FH0562 1 Snap Ring - External, 3/4" 217" Long 36' 6 Auger DAVID0518 Rear Rail 53 3FH0566 1 Snap Ring - External, 1-1/2" DAVID0543 Front Rail 54 3FH0601 1 Push on Fastener 238" Long 40' 6 Auger DAVID0519 Rear Rail 55 S-4196 2 <strong>Co</strong>tter Pin, 5/32" x 1" DAVID0544 Front Rail 56 S-1147 As Req'd Lock Washer, 5/16" Med. 250" Long 42' 6 Auger DAVID0520 Rear Rail 57 S-1054 12 Lock Washer, 3/8" Med. DAVID0547 Front Rail 58 3FH0828 2 Machinery Bushing, 3/4" ID x 1-1/4" OD x 14 Ga. 286" Long 48' 6 Auger DAVID0523 Rear Rail 59 3FH0831 4 Machinery Bushing, 1" ID x 1-1/2" OD x 14 Ga. 9 104C2013 1 Gear Motor Drive Shaft 60 3FH0832 2 Machinery Bushing, 1-1/2" ID x 2-1/4" OD x 14 Ga. 10 104C2014 1 Support <strong>Co</strong>ver - Mercury Switch 61 3FH0850 2 Nylon Flat Washer, 25/32" ID x 1-3/8" OD 11 104C2017 1 Outboard End Pivot Yoke 62 S-845 8 Flat Washer, 5/16" 12 104C2018 2 Hold Down Roller - Track 63 S-7244 2 Spring Pin, 1/4" x 1-1/2" 13 104C2025 2 Pin - Drive Wheel 64 3FH0977 As Req'd Cupped Washer, 5/16" x 7/8" OD 14 104C2026 1 Front Drive Wheel w/ Sprocket 65 S-8105 3 Woodruff Key, 3/16" x 5/8" 15 104C2027 1 Rear Track Wheel w/o Sprocket 66 FH-1309 2 Lock Nut, 1/2" NPT 16 104C2034 1 Track Unit - Rear Extension 67 1EL0425 1 <strong>Co</strong>nnector, 1/2" MPT (N/S) 17 104C2035 1 Track Unit w/ Pivot (Drive Section) 68 104C2036 1 Shield, Track Unit (N/S) 18 104C2037 1 Front Drive Wheel w/ Sprocket & Bushings 69 106E095 1 Box, Drilled 19 104C2038 1 Rear Track Wheel w/ Bushings 70 D03-0188 1 Plug, 3 Pin for D03-0122 20 104C2039 1 Roller Drive Chain - Track Unit #40 71 D03-0329 4 Standoff, Nylon #6-32 x 1/2" 21 104C2041 2 Bushing - Flanged, 1-1/2" ID x 1-3/4" OD x 1-1/2" 72 E240-1148 1 <strong>Co</strong>nnector, 4 Pin 0.200 PCB Plug 22 104E2014 1 <strong>Co</strong>ver & Fuse Holder Assembly w/o Fuses 73 FH-1309 2 Lock Nut, 1/2" with Pipe T 23 105E0021 2 Fuse Holder w/o Fuses 74 FH-1310 2 <strong>Co</strong>nnector, <strong>Co</strong>rd Heyco #3231 24 502A0036 1 Gear Motor, 230V 3.5 RPM 75 FLX-2689 1 <strong>Co</strong>ver, Electrical Box 25 PT0881 2 Bushing - Flanged, 3/4" ID x 1" OD x 3/4" 76 FLX-2690 1 Gasket, Electrical Box 4 x 4 26 PT0883 4 Bushing - Flanged, 1" ID x 1-1/4" OD x 3/4" 77 S-7393 4 Screw, MS #6-32 x 1/4" PHP ZN G 27 PT0886 2 Bushing - Flanged, 1/2" ID x 3/4" OD x 1/2" 78 S-7398 1 <strong>Co</strong>nnector, 3/8" <strong>Co</strong>rd 28 PT0925 2 Flexible Drive <strong>Co</strong>upler Section, 3/4" 79 S-7399 1 Jamb Nut, 3/8" for <strong>Co</strong>nnector, H 29 PT0926 1 Flexible Drive <strong>Co</strong>upler Insert 80 S-7931 4 Hex Nut, #10-24 SS 30 D02-0031 1 <strong>Co</strong>nnecting Link, #40 81 S-8753 4 Split Lock Washer, #6 ZN 31 7099955 1 #40 Offset Link 82 S-8778 4 Screw, MS #6-32 x 1/4" FHS ZN G 32 PT1101 1 Roller Chain Sprocket, #40 - 14 t. 83 S-995 4 Screw, MS #10-24 x 1" PHP SS PNEG-1358 <strong>Red</strong> <strong>Giant</strong> <strong>Stir</strong>-<strong>Ator</strong> 43