Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

STEP 21 Installation of gearbox drive belts - FOUR AUGER UNIT: Using two set of AX-38 V-belts, install one matched set on each end of top drive assembly. Check to be sure belt alignment is proper. Also, be sure clutch idlers are positioned as shown in Photos 16 and 17. Installation of gearbox drive belts - SIX AUGER UNIT: First, follow the instructions given for the four-auger unit. Then, proceed to bolt bearing bracket and clutch idler on to the top of the sixauger trolley. See Photo 18 and Drawing F on page 46. Next, bolt sixauger extension drive shaft into place, using two carriage bolts, 5/16" x 3/4", with lock-washers and nuts. DO NOT TIGHTEN THE 5/16" x 3/4" CARRIAGE BOLTS AT THIS TIME. BE SURE BEARING IS BOLTED IN POSITION AS SHOWN IN Photo 19. Photo 17 Photo 18 Photo 19 22 PNEG-1358 Red Giant Stir-Ator
STEP 21 (CONT’D) Using extension-shaft Delrin coupler, connect extension-shaft to top drive-shaft assembly as shown in Photo 20. Secure Delrin coupler with drive-in pin, or with steel pin and clip. Now tighten securely the 5/16" x 3/4" carriage bolts. Complete installation by installing matched pair of AX-38 V-belts. BE SURE CLUTCH IDLER IS INSTALLED AS SHOWN IN Photos 16, 17 and 21 WHEN INSTALLATION IS COMPLETE. DON’T FORGET TO FILL GEAR BOXES WITH #90 OIL! Photo 20 Photo 21 PNEG-1358 Red Giant Stir-Ator 23
Page 1: OWNER’S MANUAL Red Giant Grain St
Page 4 and 5: SAFETY GUIDELINES This manual conta
Page 6 and 7: PRACTICE SAFE MAINTENANCE Always di
Page 8 and 9: FINAL INSPECTION CHECK LIST 1. HAVE
Page 10 and 11: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 12 and 13: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 14 and 15: STEP 3 NOTE THE SEVEN-INCH DISTANCE
Page 16 and 17: STEP 10 Place the outboard pivot en
Page 18 and 19: STEP 13 Place the 3/4" x 14" axle s
Page 20 and 21: STEP 17 Bolt the drive guide arm on
Page 24 and 25: STEP 22 Installation of gearbox con
Page 26 and 27: Accelerometer lead wire Power-out w
Page 28 and 29: STEP 27 Place all belt shields as s
Page 30 and 31: to the shut-off chain so that it wi
Page 32 and 33: The augers are manufactured to allo
Page 34 and 35: NOTES 34 PNEG-1358 Red Giant Stir-A
Page 36 and 37: Red Giant Stir-Ator Overall Dimensi
Page 38 and 39: 4 - 6 Auger Shields and Electrical
Page 40 and 41: 4 - 6 Auger Trolley Base Unit Model
Page 42 and 43: Outboard Pivot End and Track Sectio
Page 44 and 45: Center Inboard Pivot End Model 176
Page 46 and 47: 6-AUGER TROLLEY EXTENSION DRAWING F
Page 48 and 49: RED GIANT WIRING DIAGRAMS Single Ph
Page 50 and 51: Three Phase - 460 Volt 50 PNEG-1358
Page 52 and 53: Three Phase - 380 Volt 52 PNEG-1358
Page 54 and 55: RED GIANT 460 VOLT TRANSFORMER HOOK
Page 56 and 57: DRAWING K DRAWING L 56 PNEG-1358 Re
Page 58 and 59: PINION SHAFTS DMC # Model # Year Fi
Page 60 and 61: GEARBOX #129 (104B2134) 104B2134 #1
Page 62 and 63: GEARBOX #150 (104B2135) 104B2135 #1
Page 64 and 65: RED GIANT TRACK DRIVE GEAR MOTOR GE
Page 66 and 67: DRYING RECOMMENDATIONS To get unifo
Page 68 and 69: STIR-GUARD OPERATION The Stir-Guard
Page 70 and 71: MAINTENANCE and ADJUSTMENTS (cont
Page 72 and 73:
RED GIANT TROUBLE SHOOTING ELECTRIC
Page 74 and 75:
RED GIANT TROUBLE SHOOTING TRACK UN
Page 76 and 77:
NOTES 76 PNEG-1358 Red Giant Stir-A
Page 78:
Red Giant Grain Stir-Ator Model 176
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?