Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

Accelerometer lead wire Power-out wire Bin wall Power connector Power-in wire Photo CC, Electronic controller enclosure assembly power wire routing. Insure that the tilt switch accelerometer assembly is installed with the arrow on the side of the accelerometer aligned with the center of the opening of the mounting bracket clip and facing toward the fuse holder box (see Drawing XX below). Drawing XX, Accelerometer assembly installation 26 PNEG-1358 Red Giant Stir-Ator
STEP 26 Position 5, 7-1/2 or 10 HP motor, mating the motor mount holes to the motor mount plate holes and securing with four 3/8" x 1-1/4" hex-head bolts, flat washers, lock washers and nuts, DO NOT TIGHTEN BOLTS, Place 4" O.D., double B-groove pulley on to motor shaft, using 1/4" x 2" square key. See Drawing C on page 40. Bolt the cam tightener ahead of the main motor directly to the motor mount plate, using one 3/8" x 1-3/ 4" hex-head bolt and 3/8" lock nut. See Drawing H on page 55. Next, place the matched BX-48 V-belts on to the 4" motor pulley, align and tighten to the proper tension as shown in Drawing J on page 55. Next, remove the capacitor cover and place 1" romex connector into side of capacitor box. Strip heavy-duty rubber covered wire approximately one foot back and install this heavy-duty rubber covered wire into romex connector and secure. Fasten cord to left side of motor support leg, using a nylon cable clamp with a #10 hex flange screw and flange lock nut. Finish by wiring motor according to Photo 27 or Wiring Diagram G on page 48. Photo 27 Drawing H Heavy rubber covered wire must be left long enough to accomodate trolley movement. Drawing “J” PNEG-1358 Red Giant Stir-Ator 27
Page 1: OWNER’S MANUAL Red Giant Grain St
Page 4 and 5: SAFETY GUIDELINES This manual conta
Page 6 and 7: PRACTICE SAFE MAINTENANCE Always di
Page 8 and 9: FINAL INSPECTION CHECK LIST 1. HAVE
Page 10 and 11: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 12 and 13: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 14 and 15: STEP 3 NOTE THE SEVEN-INCH DISTANCE
Page 16 and 17: STEP 10 Place the outboard pivot en
Page 18 and 19: STEP 13 Place the 3/4" x 14" axle s
Page 20 and 21: STEP 17 Bolt the drive guide arm on
Page 22 and 23: STEP 21 Installation of gearbox dri
Page 24 and 25: STEP 22 Installation of gearbox con
Page 28 and 29: STEP 27 Place all belt shields as s
Page 30 and 31: to the shut-off chain so that it wi
Page 32 and 33: The augers are manufactured to allo
Page 34 and 35: NOTES 34 PNEG-1358 Red Giant Stir-A
Page 36 and 37: Red Giant Stir-Ator Overall Dimensi
Page 38 and 39: 4 - 6 Auger Shields and Electrical
Page 40 and 41: 4 - 6 Auger Trolley Base Unit Model
Page 42 and 43: Outboard Pivot End and Track Sectio
Page 44 and 45: Center Inboard Pivot End Model 176
Page 46 and 47: 6-AUGER TROLLEY EXTENSION DRAWING F
Page 48 and 49: RED GIANT WIRING DIAGRAMS Single Ph
Page 50 and 51: Three Phase - 460 Volt 50 PNEG-1358
Page 52 and 53: Three Phase - 380 Volt 52 PNEG-1358
Page 54 and 55: RED GIANT 460 VOLT TRANSFORMER HOOK
Page 56 and 57: DRAWING K DRAWING L 56 PNEG-1358 Re
Page 58 and 59: PINION SHAFTS DMC # Model # Year Fi
Page 60 and 61: GEARBOX #129 (104B2134) 104B2134 #1
Page 62 and 63: GEARBOX #150 (104B2135) 104B2135 #1
Page 64 and 65: RED GIANT TRACK DRIVE GEAR MOTOR GE
Page 66 and 67: DRYING RECOMMENDATIONS To get unifo
Page 68 and 69: STIR-GUARD OPERATION The Stir-Guard
Page 70 and 71: MAINTENANCE and ADJUSTMENTS (cont
Page 72 and 73: RED GIANT TROUBLE SHOOTING ELECTRIC
Page 74 and 75: RED GIANT TROUBLE SHOOTING TRACK UN
Page 76 and 77:
NOTES 76 PNEG-1358 Red Giant Stir-A
Page 78:
Red Giant Grain Stir-Ator Model 176
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?