Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

STEP 10 Place the outboard pivot end over main frame with track drive rollers’ toward the outside. Secure with two 3/8" x 1" hexhead bolts. Place flat washers on bolt, putting bolt through outboard pivot end and frame, securing with lock-washer and nut on the inside (two on each side) then place two 3/8" x 1" hex-head bolts for four-auger machine (Two 3/8" x 2" for six-auger machine) up through the bottom of the frame, through the yoke and secure with flat washer, lock-washer and nut (Two on each side). See Photo 4 and Drawing D on page 42. STEP 11 Thread main power cord and gearmotor power cord (14-3) from the inboard pivot through the loops on the side of the main frame, with the main power cord only ending where the large loops stop. The gearmotor cord continues to the opposite end of the main frame as shown in Photo 5. Photo 4 Greenfield shown in photo has been replaced with 14-3 rubber covered wire. Photo 5 16 PNEG-1358 Red Giant Stir-Ator
STEP 12 FOR SIX AUGER UNITS ONLY: The sixauger trolley comes in two sections; one four-auger section plus an extension. First remove the bolts holding the center gear box on the four-auger section. See Photo 7 or Drawing F on page 46. Then, place two-auger section over four-auger section and replace gear box bolts. At this time, install two additional 5/16" x 3/4" hex-head bolts, lock washers and nuts in the lapped section. Be sure bolts are tightened securely. Cut loose extension drive shaft. See Photo 7. Photo 6 Photo 7 PNEG-1358 Red Giant Stir-Ator 17
Page 1: OWNER’S MANUAL Red Giant Grain St
Page 4 and 5: SAFETY GUIDELINES This manual conta
Page 6 and 7: PRACTICE SAFE MAINTENANCE Always di
Page 8 and 9: FINAL INSPECTION CHECK LIST 1. HAVE
Page 10 and 11: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 12 and 13: PLEASE NOTE: THE DECALS SHOWN ON TH
Page 14 and 15: STEP 3 NOTE THE SEVEN-INCH DISTANCE
Page 18 and 19: STEP 13 Place the 3/4" x 14" axle s
Page 20 and 21: STEP 17 Bolt the drive guide arm on
Page 22 and 23: STEP 21 Installation of gearbox dri
Page 24 and 25: STEP 22 Installation of gearbox con
Page 26 and 27: Accelerometer lead wire Power-out w
Page 28 and 29: STEP 27 Place all belt shields as s
Page 30 and 31: to the shut-off chain so that it wi
Page 32 and 33: The augers are manufactured to allo
Page 34 and 35: NOTES 34 PNEG-1358 Red Giant Stir-A
Page 36 and 37: Red Giant Stir-Ator Overall Dimensi
Page 38 and 39: 4 - 6 Auger Shields and Electrical
Page 40 and 41: 4 - 6 Auger Trolley Base Unit Model
Page 42 and 43: Outboard Pivot End and Track Sectio
Page 44 and 45: Center Inboard Pivot End Model 176
Page 46 and 47: 6-AUGER TROLLEY EXTENSION DRAWING F
Page 48 and 49: RED GIANT WIRING DIAGRAMS Single Ph
Page 50 and 51: Three Phase - 460 Volt 50 PNEG-1358
Page 52 and 53: Three Phase - 380 Volt 52 PNEG-1358
Page 54 and 55: RED GIANT 460 VOLT TRANSFORMER HOOK
Page 56 and 57: DRAWING K DRAWING L 56 PNEG-1358 Re
Page 58 and 59: PINION SHAFTS DMC # Model # Year Fi
Page 60 and 61: GEARBOX #129 (104B2134) 104B2134 #1
Page 62 and 63: GEARBOX #150 (104B2135) 104B2135 #1
Page 64 and 65: RED GIANT TRACK DRIVE GEAR MOTOR GE
Page 66 and 67:
DRYING RECOMMENDATIONS To get unifo
Page 68 and 69:
STIR-GUARD OPERATION The Stir-Guard
Page 70 and 71:
MAINTENANCE and ADJUSTMENTS (cont
Page 72 and 73:
RED GIANT TROUBLE SHOOTING ELECTRIC
Page 74 and 75:
RED GIANT TROUBLE SHOOTING TRACK UN
Page 76 and 77:
NOTES 76 PNEG-1358 Red Giant Stir-A
Page 78:
Red Giant Grain Stir-Ator Model 176
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?