Controllers - AGCO Parts

ACE Magnetic Clutch Pumps
A dependable, low cost pump
for use on self-propelled sprayers.
Rugged cast iron construction
with sealed ball bearings
allow this pump to easily handle
abrasive wettable powders.
Pump comes equipped with
heavy duty 12-volt electric
clutch for use on tractor installations
where PTO or hydraulic system is impractical. Available in either
clockwise or counter clockwise rotation. Both come with a mechanical
seal.
Note: Rotation of the pump is determined by viewing the pump from the
shaft or clutch end. Clutch pulley diameter is 5-1/4". See the Technical
Pages for more information on repairs.
FMC-MAG
Pump RPM Pressure Capacity
65 PSI 20 GPM
3950 RPM 55 PSI 35 GPM
40 PSI 55 GPM
60 PSI 20 GPM
3750 RPM 50 PSI 35 GPH
40 PSI 50 GPM
30 PSI 60 GPM
45 PSI 20 GPM
3250 RPM 35 PSI 30 GPM
25 PSI 55 GPM
FMC-CW-150
Pump Speed Pressure Capacity
45 PSI 20 GPM
35 PSI 30 GPM
3450 RPM 25 PSI 55 GPM
10 PSI 60 GPM
Data based on 1-foot lift through unrestricted
suction hose and fittings with
full 1¼" I.D.
| Part | Description |
| AG000201 | Pump, FMC-MAG, 1-1/4" x 1", Counter-Clockwise |
| AG000163 | Pump, FMC-CW-150-MAG, |
| | 1-1/2" x 1-1/4", Clockwise |
ACE Magnetic Clutch Pump Repair Parts
| Part | Description |
| AG003872 | Electric Clutch |
| AG004052 | Spacer, Clutch |
| AG000015 | Seal Viton - Standard |
| AG000016 | O-ring - Shaft |
| AG000003 | Gasket 4 Holes (used prior to 1996) |
| 6610653 | Bearing (2 Required) |
| AG000042 | Impeller, Cast Iron, Optional |
| AG000095 | Impeller for CW Pump |
| AG000009 | Shaft, S.S., LH Course Thread |
| AG000094 | Shaft, S.S., RH Fine Thread |
ACE Frame Mount Pumps
Ace Model FMC offers a dependable, low
cost pump for use on self propelled
sprayers or mounted on a base for electric
motor or gasoline engine drive.
These pumps feature sealed ball bearings
and a readily replaceable mechanical
seal. Easily handles abrasive wettable
powders.
Ace Model FMCH features an increased
pressure range. Grease lubricated lip-type seals located in impeller
intake area eliminates pumping pressure on seals thereby increasing
seal life. Grease protects seals when running dry.
Note: CW - Clockwise Rotation.
| Part | Description |
| AG000155 | Pump FMC, 1-1/4" x 1" |
| AG000156 | Pump FMCH, 1-1/4" x 1" |
| AG051610 | Pump FMC-150, 1-1/2" x 1-1/4" |
| AG726888 | Pump FMC-CW, 1-1/4" x 1" |
| AG000181 | Pump FMC-CW-150, 1-1/2" x 1-1/4" |
| AG000182 | Pump FMC-CW-200, 2" x 1-1/2" |
| AG000129 | Repair Kit with Viton Seal for FMC |
| AG000130 | Leather Lip Seal Kit for FMCH |
SpraCoupe Replacement Pump
Ace's new replacement pump is a direct
replacement for the Hypro pumps on Spray
Coupe models 3430, 3440, 3630, 3640, 4440,
and 4640.
Features:
• Suction 1-1/2" Discharge 1-1/4"
• Clockwise rotation when facing pulley end
• Chemical resistant Valox impeller
• 3/4" Diameter stainless steel shaft
• Standard Viton seal
• Heavy-duty DC 12-volt magnetic clutch
transmits up to 44 HP at 4000 RPM
Feature Comparisons:
• Pump Bearings are 204 Heavy-duty compared to 202
• Pump Shaft is 3/4" compared to 5/8"
• Clutch rating is 58 ft lbs compared to 30 ft lbs
• Clutch Bearings 2 as opposed to one
• Clutch Pulley machined steel as opposed to stamped steel
| Part | Description |
| AG000154 | Pump FMC-150-Mag-DX3 |
Pumps
69